gc8 3d models
24 3d models found related to gc8.thingiverse
I made an adapter for the blinker reset on my JDM 1999 GC8 Impreza WRX STi clockspring, so I could use a USDM 1999 Legacy clockspring. ...The legacy clockspring was more readily available and cheaper than a JDM one..
thingiverse
Converter for normal GC8 Dump-Vale to wrx Dump-Valve.
thingiverse
Mount your gauges in the Center console with this mount made spezifically for Subaru Impreza GC8 (Created on a WRX model) Trimming of the center console nessesarry as well as making it blend in. Made for 52mm gauges. Middle hole is for the cigarret...
thingiverse
Replacement blanking and switch housing plugs for the center console on a Subaru GC8. ...3D models include; Blanking plug 13mm switch housing plug 20mm switch housing plug Please help support my work and hit "Tip Designer" Print Settings Printer: ...
thingiverse
Hood prop clips for a Subaru GC8. Both left and right clips are included. Left and right as viewed from behind the fly wheel. Clean models are provided as well as models with built in supports. Supports are easily snapped off after printing! -edit-...
thingiverse
Gauge panel for 53mm gauges with 60mm facering. My old one couldn't fit the new gauges, so I designed and printed this one. Remarks: Check if it fits the printer (210x72x6mm) To install these gauges, you will need to edit the dashpanel...
thingiverse
Door Trim Cap for Subaru Impreza GC7 and GC8, based on the 94222FA120ND item.
thingiverse
Replacement side indicator clip for a Subaru GC8. ...Please help support my work and hit "Tip Designer" Print Settings Printer: Myriwell ...
thingiverse
Replacement 3D printable cable tidy clip on oil filler tube for Subaru GC8. May fit other models. Please help support my work and hit "Tip Designer" Print Settings Printer: Myriwell ...
cults3d
About 1/24 scale (Can be rescaled) Model 1: 12,90 x 49,05 x 6,98 mm Model 2: 12,90 x 49,05 x 8,05 mm For commercial use of the files, contact me first Attention: -Adjust the size to fit your model -Take care when you remove the supports -Part should...
thingiverse
This is a mount for a Voodoo Manual Boost controller (or any common MBC). It replaces the removable ashtray part that clips in and out of your dash (present on my 95 STI, check to see if your Subaru has the same part). There is zero modification of...
thingiverse
This is a work in progress and I'll add notes if things are updated... I wanted to share this for those who needed a way to mount their IAG AOS in their swapped impreza (93-01). I made this mount as the mounting options for the classic Impreza's...
thingiverse
This is designed to be an intake silencer delete for my V1 WRX (EJ20G). It is still a work in progress, but it does function as I intended. Your mileage may vary and I am not responsible if you grenade your engine. I did not include the IACV or...
thingiverse
I ordered new LED's to go into my Fog Light housings and the heat sink was too large. I made these to go over those and still screw into the housings. I printed it in PETG. Supports are built into the file. ...You'll have to flip it 180 to get it to...
thingiverse
Adjustable 3D printable cable tidy clip on oil filler tube for Subaru GC8. May fit other models. This part will snap together after printing. This is a re-think/re-work of my original design. ... https://www.thingiverse.com/thing:1619117 ...
cults3d
This is a 3 piece replacement vent for the factory 1996-2001 Subaru Impreza WRX hood scoop. This design offers 5mm flat plates that are easier and faster to print than the Lunchbox vent. Plan on 12-16hrs to print instead of 20. Qty 6 M8 x 45 bolts...
cults3d
The model is divided into 4 parts Subaru car Tire Hubcap Airfoil
cults3d
This assembly replaces the factory Subaru WRX hood scoop from 1996-2001. If you have swapped intake manifolds to a taller 04-05 manifold with spacers, then it likely fouled the hood and required a hole to be cut at the mouth of the factory scoop. It...
cults3d
Its getting pretty hard these days to find old school plastic JDM car parts. Also finding somewhere to source the parts can be to much of a mission. This particular model is already scaled to fit the bumper 100%. Me personally i printed this model...
thingiverse
Insignia de baul subaru impreza GC8 medidas originales
thingiverse
Rally car roof scoop for air vents. ... Can be customized to fit any vehicle, however this one is being designed to fit the Subaru GC8 rally car roof.
thingiverse
As the description says, this is a cap and a pin for the OEM air box on a 1985 Honda Aero 80 part number 17241-GC8-000 ***Pin (Bolt38mm) must be printed horizontally for structural integrity***