gcode cat cr 10 3d models

This is an E3D Volcano mount specifically designed for the Creality CR-10/Afinibot A31 printer. It maintains the original nozzle height from the bed while adjusting it slightly closer to the front edge of the bed, a detail that still requires testing...

... coordinate all my mechanical parts into harmony. I imported the vent-ring-short-2 design into Tinkercad and reduced the vertical chamber height by 1 mm. The result is a print that just barely clears the bed and prints flawlessly on my stock CR-10.

... to the frame with a screw and a T-slot nut, which I conveniently sourced from my spare parts stash. This wire guide is fully compatible with the CR-10 Ultimate Leveling Knob Attachment from Valstrath, making it an easy addition to my printer setup.

Fan shroud for the PSU unit on the CR-10 Max. Model is done to minimise the material used, thus the wall is thin. I printed it with 0.6mm nozzle with 0.8mm line width (the wall thickness) and 0.3mm layer height. ... you can use a 0.4mm and push the...

This is a revised version of the original CR-10(S) TUSH spool holder for mounting over the control box. I found the original design left me feeling uneasy with the spool resting directly on the bearings, so I added some rollers to center it properly....

It should work with any printer that uses the same kind of V-slot as the CR-10/s so long as the hotend carriage doesn't have a collision aspect on the reverse side of the rail. Uses one of these COBs:...

I recently bought a Bl Touch for my CR-10 V2 and was unable to find a mount that made use of the factory mounting point. This solution worked perfectly for me. ... The mount functions incredibly well with the tinymachines3D source code, which requires...

I didn't want to opt for longer 3mm bolts, so I wanted to stick with the original CR-10 thumb screws. To assemble this remix, you'll need T-nuts and 5mm bolts that are 10mm long for the larger holes. ...Additionally, you'll require two small 3mm nuts...

I'm currently using a custom spool adapter that I created to fit perfectly on the standard CR-10 spool holder. I wasn't completely satisfied with the existing adapters, so I decided to try a different approach. One of the advantages of this design is...

The y-axis belt of my CR-10 was torn apart due to damage from the initial endcap. I obtained a replacement belt and created an alternative endcap that would not harm it. It's essential to note that the new belt must be longer than the original one,...

Cable support for stock Creality CR-10 Max. It securely holds bowden tube and cables from the hotend/extruder. Avoids wearing of the cables due to the movement of the carriage. Prints in two parts, no supports. For attaching the parts together...

I created this auto bed leveling test as an effortless way to auto level the bed on any CR-10 3D printer. How To Use: Navigate through the auto level feature with a sheet of paper and level all of the bed. Then run this test print and adjust as...

I wanted to make mini version of prusa i3 mk3s with bowden setup using cr-10 hotend. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Sunlu PLA+ Black Category: 3D Printer Parts

This tool holder is specifically designed for use with Creality's CR-10 Max, and I created it using Solidworks 2019. You can also access the Solidworks Files, along with .IGS, .STEP, and .X_T files, by extracting them from the included RAR file. When...

This is a compact hotend fan mount / shroud for the Creality CR-10 with t-slots for attaching anything you want.It also allows for greater adjustability and makes it easier for future changes.Included is a fan guard, a layer fan duct for the original...

A custom-designed Case Mounted Filament Holder is tailored to accommodate larger spools weighing up to 2.5kg, specifically for use with the Creality CR-10. I based this design on my own case dimensions, focusing on width, so if newer models have...

This light installs on the backside of the top bar on the CR-10. It fits three rows of SMD3528 LED and uses a KCD11 switch. Also, lining the inside with foil tape boosts reflectivity even further. You can either print the diffuser or use a thin piece...

Now, it fits perfectly on my CR-10 when in the home position on the z-axis. I created this design using TurboCAD 2017. This is the dial indicator model I used: https://www.amazon.com/gp/product/B016R3GLB0/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 ...

It holds the original PSU coming with the CR-10, if you want to convert the classic CR-10 into a boxless version (similar to the Ender 3). The mains voltage section of the PSU is seperated from the output voltages and contains no...

I upgraded my CR-10 V2 to a V3, and I noticed that I was having some banding issues with printing. It was suggested I print or make one of these to fix the issue and it helped a lot. Anyway, This spacer\bushing helps prevent the jerking that...

I wasn't thrilled with the factory lead screw bearing blocks on my CR-10, as they were excessively tight and seemed to resist movement if the alignment was off even slightly. To address this issue, I engineered these custom blocks to utilize 608ZZ...

Customize your CR-10 (or clone) with the perfect colored rail inserts! Replaces stock units with any color you desire, available in 20mm, 40mm, 60mm, 100mm, 200mm, and 400mm lengths to suit every need. Works seamlessly when printed in vase mode with...

A Customized LED Light Strip Fitting, Designed to Fit the Tevo Tornado / CR-10 Maximum Bed Size. To secure this fitting on top of the Z bar, use three M5 cap head bolts measuring 16mm, paired with three T 5mm nuts. Two 8mm LED light strips are...

It should work with any printer that uses the same kind of V-slot as the CR-10/s so long as the hotend carriage doesn't have a collision aspect on the reverse side of the rail.Uses one of these COBs;...

If your spool doesn't fit snugly into your CR-10 holder, there's a simple solution. Try working with threads that are more accommodating. For those who want a longer explanation or have questions, feel free to leave a comment below. If you notice any...

This is a universal mount that fits onto the CR-10 V2 and V3 stock hot end housing. intended for remixes as it allows you to easily attach anything to your printer in seconds. ... it snaps on over the housing requiring no tools or screws and...

To secure the actual adapter in place, I employed a Command adhesive strip atop the box, while another strip was used to attach the enclosure itself to the CR-10's control panel. ...As my proficiency with OpenSCAD continues to grow, I plan to take it a...

The CR-10 V2 boasts several notable upgrades over its predecessor, but one area that still requires improvement is the wire harness. Currently, the wire harness attached to the gantry assembly is left hanging from a connector, which can cause the...

Having a CR-10 Smart at home and at work, I kept forgetting which nozzle size was in which printer, so I made these to sit on the top of the printer in the groove of the top rail. &nbsp;</p><p>Used a little paint on the numbers to make them stand...

This is a universal mount that fits onto the CR-10 V2 and V3 stock hot end housing. intended for remixes as it allows you to easily attach anything to your printer in seconds. ... it snaps on over the housing requiring no tools or screws and once in...