ge profile replacement knobs 3d models
224852 3d models found related to ge profile replacement knobs.thingiverse
This is a replacement knob for the smaller bridge and large/small selector switch on the GE Profile Cook-top JP989B0D6BB. The hole is 6.5mm to fit the peg and 10.5mm deep. There will be a small circle of waste plastic left over from the raft in...
thingiverse
Stove Knob This is a simple replacement for a GE Profile range stove knob (may fit others as well) that I created from scratch to replace a broken knob. The key to the knob is the profile that is used to cut out the key hole on the bottom. I designed...
pinshape
Summary Hi guys I made this cooktop knob for my electric GE profile, one of mine was missing and since I have a 3d printer I decided to make one, so if you have the same problem I hope this help you, thank you for downloading and don't forget to...
thingiverse
Hi guys I made this cooktop knob for my electric GE profile, one of mine was missing and since I have a 3d printer I decided to make one, so if you have the same problem I hope this help you, thank you for downloading and don't forget to like. If you...
thingiverse
GE Profile cooktop stove knob (WB03T10236). This design is composed of 2 parts, a knob and shaft adapter. The shaft adapter is printed separately to allow the knob to be printed flat on the printer bed without the need for supporting structure. The...
thingiverse
Print Settings Printer Brand: Solidoodle Printer: Solidoodle 4 Rafts: No Supports: No Resolution: 0.3 mm Infill: 50% Notes: The knob is not hollow like the original. It is filled and designed to be printed flat and without supports. Printed using...
thingiverse
Here are my clones of the left and right front trim panels for a GE Profile stove. There are no parts in existence for this model, and both trim pieces were broken. I tediously reconstructed the complex design by taking photos and measurements in...
thingiverse
The front rollers for the bottom rack of the dishwasher in my new place were missing which caused the bottom spray arm to rub against or get stuck to the rack. ...This fixed the problem.
thingiverse
A replacement knob for a GE washing machine model WXCR1070T. ...Print Settings Printer Brand: RepRap Printer: Mendel...
thingiverse
Replaces the easily broken freezer basket mounts in GE profile refrigerator model# PFS22SISBSS. 4 are needed. ...PETG at 50% infill has worked well so far.
thingiverse
This is a bracket for a GE microwave handle profile series. ...The radii are not perfect yet, i will update this when i fix that, however it is a really close fit!
cults3d
I have a door that needs a low profile knob. Here is my attempts to replace them. ... Included in the SKP file there is a base to create your own knob.
thingiverse
I have a door that needs a low profile knob. Here is my attempts to replace them. ... Included in the SKP file there is a base to create your own knob.
thingiverse
This is a replacement part for GE Fridge GTS18FSLCSS. This piece is very brittle and seems like it would be a common failure mode for this fridge. ... I printed it in PETG and it feels stronger than the original part.
thingiverse
ABS Filament 100% Infill These knobs will replace broken factory knobs on the Motorola XTS 1500 radio (PRC 153). The volume knob is a press fit over the metal stud left after removing the old knob. Leave the orange rubber seal in place, but remove...
thingiverse
$25 for a single replacement knob for my Jenn Air Stove Model number JDS9860BDB, screw that. I have a 3d printer. There are two knobs in this set; one normal, you will need to print 3, and one with Sim (Simmer knob) if your stove has that. I...
thingiverse
This is a Wheel for the upper rack of GE dishwasher other one melted after a few years of operation so i measured it and created this Fits in with little effort rolls and holds the rack where it needs to b. ...
prusaprinters
Made some knurled knobs for the excellent Prusa MK3S. ...Sizes D15, 20 and 25mm. This is a remix of the original Prusa MK3S LCD knob.
thingiverse
Replacement horn for the Aristo-Craft U25B loco. ... Part#22100-37 Equivalent.
thingiverse
An inexpensive one is the "R4Dry4" which features two knobs that seem to be easily broken (assumption based on the fact that this is our second unit which has had knobs break and I've seen others). Having tried gluing the factory knobs without luck...
cults3d
An inexpensive one is the "R4Dry4" which features two knobs that seem to be easily broken (assumption based on the fact that this is our second unit which has had knobs break and I've seen others). Having tried gluing the factory knobs without luck...
prusaprinters
Replacement horn for the Aristo-Craft U25B loco. ...Part#22100-37 Equivalent.</p><p>Siraya Tech Resin</p><p>Smoky Black</p>
thingiverse
Replacement part for GE Profile Dishwasher PDW7880G00SS upper rack roller slide. Part # WD12X10065. ... Reference: https://www.geapplianceparts.com/store/parts/ModelSectionParts/PDW7880G00SS/3/0/0/0/UPPER_RACK_ASSEMBLY
thingiverse
You may need to enable a bit of negative horizontal expansion in Cura or the equivalent setting in your preferred slicer to ensure that the knobs fit on the shafts; the design leaves just enough room assuming perfect dimensional accuracy. I found...
thingiverse
This handle/spacer slips over the front of the ice drawer in GE "Profile" Refrigerator with freezer on the bottom (PFSS2MIYI SS). It provides just the right spacing to close the ice drawer when the main freezer drawer is closed. All too often, when...
thingiverse
I just need a quick replacement knob. Printed on a MB Gen 5. ...100% infill.
thingiverse
A replacement door handle for a GE dryer. ...The original part number was 175D1372.
thingiverse
This is a set of replacement knobs for my broan range hood. They have the advantage of being larger and easier to grip. For some reason, the old one stripped itself out so I spent some time and made new ones in OpenSCAD. The source is...