geeetech a10 direct drive 3d models

I've created a similar design for the BLTouch sensor, which you can find here: https://www.thingiverse.com/thing:3464552 As you can see, I've connected this mount directly to Geeetech's Extension Board using the Extension Board Mounting Plate...

... solution. You screw a filament runout sensor at the top. It also ends up functioning as a filament guide for your direct drive setup. It works very well in combination with my direct drive spool holder: https://www.thingiverse.com/thing:5014985

Ender 3 Direct Drive Extruder Mount DirectDrive RE v10.stl DOES NOT INCLUDE BLTOUCH MOUNT Converts standard bowden extruder to direct drive and adds a bltouch mounting point. ... Set aside fan shroud by removing screw on back Remove track roller spacers...

Another version of Direct Drive Extruder, this one with PG35L motor and reprap discount Hexagon hotend and drive gear. http://www.reprapdiscount.com/hotends/67-hexagon-hotend-set.html http://www.reprapdiscount.com/mechanics/52-hobbed-pulley.html#...

Custom X-carriage boosts direct drive extrusion capabilities, seamlessly accommodating a standard Tevo Nema 17 stepper motor. ... Leaving a like shows appreciation, while made pictures really make the build shine.

This is an 18mm sensor adapter tailored specifically for the direct drive carriage, a precise replica of Prusa's design, engineered to seamlessly integrate with Anet A8 and similar printers.

Direct Drive Extruder Mount for Ultimaker 2 Clone with MK8 Extruder Print Settings: Printer: Anet A8 Rafts: Irrelevant Supports: Unnecessary Resolution: Set to 0.2 millimeters Infill: Optimized at 25% density

resized the knob end to be smaller to accommodate the smaller space with the direct drive setup. the shaft hole was left unchanged but didnt fit without filing etc. the hole was to small. Palodion... ...thanks for the design.

I designed my own to replace the one that wasn't satisfactory, which was the only available option. ...I used two new screws, each measuring 3 by 10 millimeters, to attach it directly to the titan's drive.

Direct drive extruder adapter remixed for use with a Micro-Swiss extruder. Print laying flat on its back with support. ...I would recommend 100% infill on at least the screw part.

Recently i have bought one of direct drive extruders. And here is a model of stock fan duct. ... DDE from here https://ali.onl/1Yfz PLS contact me if you need improvement of more precise model.

Direct Drive (BMG & BMG clones compatible) setup for CR10-Smart Rev 1 10 April 2022 Changed the previous part cooling fan duct to CR10smart_Cooler00a.stl previous one was hitting to bed adjuster.

This is a Satsana hot-end shroud for the Voxelab Aquila with a 5015 blower fan and I removed the cable management tabs on the top to accommodate a direct drive mount for the Sherpa Mini. ...

I got a filament dryer and needed a way to guide the filament from it to my direct drive extruder on the Ender 3. This is mounted to the top extrusion. ...I printed it in PETG for better layer adhesion.

Filament sensor for Ender 3 for direct drive extruder. ... What you need: - pen spring - ball bearing 688 - ender end stop - silicone grease (optionaly) - screw m2 x2 - threaded insert m2 x2 - m3 screw and nut x3

Spacer for the BLTouch Mount on the TriangleLabs Direct Drive Extruder Kit. The Springs Are Not Required, as a 4mm Spacer Is Sufficient. ...The Real BLTouch Has a Z Probe Offset of Approximately 2mm.

This is a direct drive adapter for the Creality Ender 3 made to work in conjunction with the satsana duct: https://www.thingiverse.com/thing:4623647 and using only stock components

Direct Drive Extruder mount for cr10s pro v2 Print Settings: %60 infill support yes Extra part needed will be longer stepper motor cable like this https://amzn.to/39IUygt or Cable motor extension cable Enjoy !

This is is a remix for the linear rails version of the Microswiss direct drive extruder kit for wire and strain relief. ...If you find any issues let me know.

Recently i have bought one of direct drive extruders. And here is a model of stock fan duct. ... DDE from here https://ali.onl/1Yfz PLS contact me if you need improvement of more precise model.

This is a direct drive adapter for the Creality Ender 3 made to work in conjunction with the satsana duct: https://www.thingiverse.com/thing:4623647 and using only stock components

I whipped up a custom mod for myself, figuring I'd share it with others. ...This mod is designed to fit the Petsfang Direct Drive Mount rather than the Titan one, allowing you to utilize your stock extruder seamlessly.

I designed a custom bracket to support the installation of a Titan Extruder Clone on my CR-10S Pro, upgrading it to a direct drive system. ...The bracket accommodates a 23mm pancake stepper motor for precise and efficient operation.

dual part cooling fan i made for my ender 3 with a microswiss direct drive. fitment is perfect for a 4020 fan. designed for heat inserts to mount the fans. ... works really well.

I took the original connection STL into Tinkercad to extend the base 8mm to make this compatible with a direct drive microswiss and it works very well. ... Bridging test and Benchy photo: https://imgur.com/gallery/pu7vBOD

Remix of the filament guide from Matt, tailored specifically for use with a Direct Drive modded Ender 3 Pro. ...To achieve this, I shortened the arm and introduced a precise 1.8mm gap.

Find here the files required for printing a 40mm fan, compatible with Printrbot's Direct Drive Extruder. ...These files have been adapted from Brooke Drumm's basic Laser Cut templates for enhanced printability and simplified assembly.

A direct-drive extruder model features a head placement, and upon functioning, I'll share a video. ...The initial design is by Tito, which can be found at http://www.thingiverse.com/thing:110269.

Just a simple cover for the Ender 3 Direct Drive plate mounting the Hero Me 5. Print upside down! ----------------------------------- Una simple carcasa para el plate de extrusión directa para la Ender 3 montando el Hero Me 5. ... Imprimir...

When switching the D-Bot over from Bowden to direct drive, human operators need to adapt the X endstop on the carriage. ... Print Settings: Printer: D-Bot Rafts: No Supports: No Resolution: 0.2mm Infill: 70%