geeetech a20m 3d models

I made this adapter because the original knobs of the geeetech a20 are too small and not very precise. Attention! ...the knob behind the left must remain small due to collision with the Y stepper!

GEEETECH GT2560 Board cover for Prusa i3 pro B, i made holes for fixing nuts with soldering gun and fix them with silicon gun, if you prefer you can make trough holes.

Simple frame for touchscreen. ...Print Settings Printer: GeeeTech A30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Other PLA Post-Printing ============= Use double sided scotch tape to fix the frame. ... Category: 3D Printer Parts

This is an upgrade for the GEEETECH I3 Wood 3d printer. Each part is assembled using the connecting components supplied with the printer and advanced. ...I only added ball bearings (hole 8mm) for z axis threaded rods.

Replacement for stock extruder fan duct - Geeetech A10M 2 (dual colour). Print in orientation as shown in image #3. Supports = touching build plate only. Original bolts used. Designed in Fusion 360. ...Sliced in Cura (4.5)

A Holder for the Standard Tools from Geeetech Printers and for a few Nozzles, a caliper and a socket wrench, to mount e.g. ...on a Ikea Lack Table

<p>To bring a new use for the empty Spool. ...I designed it for a Spool from "GEEETECH".Just need a drill to make a 5mm diameter hole.Enjoy!

Ring Air Duct for GeeeTech A10T, may fit A10M, A10, and other models too. ... Aerodynamically designed Material: PETG Layer: 0.15mm Supports: Tree type after >70°, from building surface only Infill: No Nozzle: 0.4mm

I made this adapter because the original knobs of the geeetech a20 are too small and not very precise. Attention! ...the knob behind the left must remain small due to collision with the Y stepper!

I swapped out the Sanguinololu in my Prusa i3 with a Geeetech GT2560, giving it an extra set of mounting brackets that allowed for a snugger fit. ...I then printed up replacement brackets for two machines.

I employed Geeetech filament and configured settings as follows: a nozzle temperature of 230 degrees Celsius, a bed temperature of 70 degrees Celsius, and a fan speed ranging from 30 to 70 percent.

Ring Air Duct for GeeeTech A10T, may fit A10M, A10, and other models too. ... Aerodynamically designed Material: PETG Layer: 0.15mm Supports: Tree type after >70°, from building surface only Infill: No Nozzle: 0.4mm

Better fan for the Geeetech A20(M)Parts needed:-5015 fan-2x M3x25Print the duct with the large side facing the buildplate.

Bearing Spool Holder Geeetech Inner diameter: 32.2mm Outer diameter: 51.5mm Watch the assembly process on YouTube at https://youtu.be/Mi2JIFx1DWg or visit our tutorials page for more information at https://youtu.be/nwLfWNKTt8E

Design for Geeetech Aluminium Printer Settings Printer Brand: Prusa Printer Model: Prusa Clone Rafts: None Supports: None Infill Percentage: 15% Notes: Rotate model 90 degrees along the X-axis.

Extension to the original acrylic spool holder for 270mm filament spool designed for Geeetech printers. Print Settings: Printer: Geeetech i3 Aluminum is used as the printer model. Raft Settings: The raft setting can be set to any value, as it does...

I required a mount for a 40mm fan and a 3D touch sensor on my Geeetech I3 Aluminum Mk2 printer - and merged them from these two designs: JimmyShawsTidBits 40mm fan bracket, which can be found at https://www.thingiverse.com/thing:1492650, and...

Geeetech's replacement x carriage back-plate is designed specifically for use with the original bearing and clamps that come with the kit. ... The extruder support was remixed from someone else's design that I no longer have access to, but I'd like to...

... simplicity's sake. Notably, the heatbreak to heatblock screws on the Geeetech A10 are tightened all the way down, establishing a precise distance of approximately 47.3mm. ...This distinct feature allows designers to account for it in their designs.

Made this because the center of the spool of the Geeetech filament I got was so large it didn't spin very freely, Its also can be used to mount the filament on a dremal 3d printer. Its a 75 MM outer diameter I had another Geeetech that was smaller...

Print Settings: Printer: Geeetech Aluminum Prusa I3 Rafts: No Supports: No I started by sketching out the design in my mind, thinking about how I could create a dual fan mount that would work seamlessly with the factory mount points on the steel...

The Geeetech 3D Touch Shield is a cutting-edge innovation in 3D printing technology, designed to revolutionize the way you interact with your printer. This shield seamlessly integrates with the Geeetech 3D printer, elevating it to new heights of...

Geeetech SmartLCD Case: Visit http://www.thingiverse.com/thing:117932 Print Settings: Printer Brand: RepRap Printer: peursa i3 Rafts: None required - feel free to skip this step! Supports: No extra support needed for a smooth print. Resolution:...

The top-mounted console didn't impress me though - I found it too flimsy and opted for the more robust design of the Prusa Original instead.\r\n\r\nThat's why I created this console replacement that can be easily installed on my Geeetech. It fits...

Print Settings Printer: Geeetech A10 Rafts: No Supports: Doesn't Matter Resolution: 0.2mm Infill: 15% Filament: Grosssiste 3D PLA Silver Notes: You can print on the flat surface or on the back with minimal support (tree supports). In my case I added...

... side port. To get longer range I used a USB extender cable, and it works great. The mounting holes are close to being perfect. This should work on other Geeetech models as well, along with any other board that uses the Creality hole pattern.

Merci Héliox :) ------------------------------------------------------------------------------------------------------------------------ Allows to mount a rotary cutter on a Geeetech A10 Modification of the original Heliox model. Clip the lugs...

Geeetech Prusa I3 Axis Wobble Fix by ShawDreamer, Published September 17, 2016. I Made Some Improvements! Added an Adjust Screw Stabilizer to Get a Better Result. Reversed the Z Nut for Enhanced Stability. Included a Printable Model for You to...

I possess the Geeetech i3 pro C. The z-axis exhibited wobbling, prompting me to create smaller replacement parts and test their functionality first-hand; they worked seamlessly. I subsequently crafted larger components, completing the upgrade in a...

This is a spring seat designed specifically for the GEEETECH i3 Pro B 3D printer. It perfectly fits onto the heat bed and z-axis bottom, ensuring that the spring remains centered at all times. ...The latest update enables users to load up to ten objects...