geiger counter case 3d models

A complete Geiger counter case to hold the Geiger counter electronics, power supply, and tube using the kit from https://sites.google.com/site/diygeigercounter/. The kit consists of the base, lid, and protective covering for a VA-Z 115 tube, along...

GMC-320 geiger counter case

Simple geiger counter case for the kit linked below. Simple magnets can be inserted/glued to snap the case lid closed. Simple install, simple print. Shouldn't require supports. ...Let me know if you have any issues.</p><p>Kit</p><p><a...

Case for Geiger counter kit I brought from eBay. ...fix

Case for the cheap geiger counter. Pictures show prototype. ...Just snaps in to the support plate under the pcb.

Its a case for the Open Hardware Geiger Counter from MightyOhm Made out of 3mm Acrylic and some M5 and M3 bolts. ... Instructions Sandwich and bolts are all you need.

Its a case for the Open Hardware Geiger Counter from MightyOhm Made out of 3mm Acrylic and some M5 and M3 bolts. Instructions Sandwich and bolts are all you need. Category: Other

This is a Very simple case for the Sparkfun Geiger Counter I printed using my PRUSA MK2S. I just need a case to protect me from the high voltage area on the PCB. If you like it or even just try it out please let me know your thoughts. ...

A case for the SparkFun Geiger Counter, SEN-11345. This has cutouts for the sensor, power switch, and USB cable, and elevated pads to screw the board down to. I removed the supplied feet and used some self tapping screws to secure it to the case...

Case for Geiger counter module from Aliexpress: https://www.aliexpress.com/item/1005002424234892.html?spm=a2g0s.9042311.0.0.27424c4dCp3KaJ Also you need: Charging module:...

Therefore I'm able to connect the geiger counter to my Home Assistant + I added a small OLED Display, to see all data directly when standing in front of it (+ 10 coolness).After the electronics where finished, I've designed an enclosure, based on the...

A handy case with a detachable probe to house your Geiger Counter kits. I designed it to fit the DIYGeigerCounter v.4.1 board (https://sites.google.com/site/diygeigercounter/). I've included a version without standoffs for those of you who wish to...

A handy case with a detachable probe to house your Geiger Counter kits. I designed it to fit the DIYGeigerCounter v.4.1 board (https://sites.google.com/site/diygeigercounter/). I've included a version without standoffs for those of you who wish to...

If you have the current version (with four standoffs) check out my other design here: https://www.youmagine.com/designs/gieger-counter-case-for-gk-mini-v2-x This is a case for the GK-mini geiger counter kit. More info on the kit can be found by the...

I picked up a MightyOhm Geiger Counter Kit from AdaFruit.com just for the heck of it. It's a fun and cute little project. Unfortunately it comes as just a board and parts, with no case. So I designed and printed one for it. Print Settings Rafts: ...

#Mighty Ohm Geiger Counter Enclosure This project was realized while streaming live at https://www.twitch.tv/chrisfigge.  Years ago i bought a geiger counter kit at chaos communication congress. Time flew by and i forgot about it. A few month ago I...

Instructions -Print the case and lid in the material of your choice (I used black ABS) -Insert geiger counter PCB into case and make sure everything lines up. Due to warping and inaccuracies with my printer, I had to slightly drill out the screw...

Do you have a model BR-9B Geiger counter and are you looking for a durable case? This item could be for you! It is designed to be hung around the neck so as to keep track of the radiation that is absorbed by the body but this does not mean that you...

If you need one though, it's a good compromise from the really expensive ones and it does work reasonably well (Tested with a Geiger counter test strip - available on Amazon and eBay.) It generates pretty high voltage (390 volts) to operate the...

Made this Remix of the case to allow mounting an ESP32 with an accessible micro USB port for programming. ...Use m3 hardware to mount the ESP.

(The photo shows the older kit in the new case, which is why there are only three display screws.) If you have the earlier version with three standoffs, you should check out my other design here: https://www.youmagine.com/designs/geiger-counter-case...

customized with 3D Slash, added port ability for serial and ttl connections (for logging and usb). same settings as original design. ...Print Settings Printer Brand: SeeMeCNC ...

---------------------------- A cosmetic only spin on the MyGeiger v3 pro case by Karlosek, made for dual filament printers. From the original design by Karlosek (https://www.thingiverse.com/thing:4202730): This is a box for MyGeiger ver.3...

Small case for Geiger counter kit from Pollin Electronic (www.pollin.de Part no. 810 223). Simple case with access to LEDs, switch and display. Has a little 9V-box and a rear cover. Designed to be printed without supports. The PCB is hold in place by...

Case for RadiationD-v1.1 (CAJOE) Geiger Counter GC-1602-NANO.Plexiglass flesh with the wallsPower sockets and on/off switch accessible.No hole for the audio jack.

... oled display. ... It is customizable in case you need to adjust some values Video: https://spectra.video/w/j4V3S5YeiwPztV6c2pn2u7 Code: https://github.com/Vault2501/Geiger-Counter-Cajoe Pictures: https://pixel.tchncs.de/i/web/post/586695111360716092

I have created a housing for the Geiger counter GC-1602-NANO (CAJOE v1.1).I left openings for the connections on both sides.With the Plexiglass cover and the spacers, the Geiger counter fits exactly into the housing and closes flush.More information...

This is a case I designed for the MightyOhm Geiger Counter kit: http://mightyohm.com/geiger Instructions Material: 1/8" thick cast clear acrylic Cut with laser cutter. ... All lines are vector cuts.

-------------------------------------------------------- Case for Si8B pancake Geiger counter sensor which also offers space for an electronic converter (just place it on top of the sensor into the front part of the case; I soldered mine directly...

Remix added slot for SD and access to external power. Also modified to use a wall mount. ... ------------------------------------------------------------- Updated 17/07/2017 Modified top to add possibility to put a button to turn on/off lcd...