geprc cinelog 25

M5 25
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: counter sink = 2 steps step shape degrees = 45 thread outer diameter = 8 slot depth = 2 inches head diameter = 12 inches slot width = 1 inch wing...

25.12
thingiverse

https://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: Thread Type - standard Thread Length - 605 units Resolution - 0.5 increments Outer Diameter - 26 units Countersink - 2 degrees Head Diameter -...

25' square
thingiverse

Grid size is set to 25 squares. Magnet size is 5.6 units in diameter. Grid height is 2 units. The plastic saver feature is turned off. Random variation minimum is set to 0. No incline is applied along the Y-axis or X-axis. Height of the design is 1...

5cent-25
thingiverse

For this particular model, parameters include one tube, 0.4mm clearance, a tube wall of 2, coin type 5, and 25 coins. The model also features tube generation (set to 1) with a fudge factor of 0.975 and cap generation (also set to 1). SCH Edit:...

I 25
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 25 gopro_primary = double gopro_bar_screw_d = 3 gopro_bar_screw_nut_d = 6.01 gopro_bar_th = 3.2 gopro_ext_th = 3 gopro_rod_nut_od...

.25 pump
thingiverse

**Instructions** Operating with the following settings: Wire size = 6.7 mm Plate height = 45 units Torque value = 25.4 in-lbs Drill speed = 101 revolutions per minute Tolerance setting = 0.15 percent Number of planetary gear trains = 3 systems...

25 dimple
thingiverse

**Instructions for Using the Options** The following settings were used: Size was set to 25 millimeters. A resolution of 26 dpi was selected. The ratio of the sphere's lid was adjusted to 70 percent. By default, density was left untouched with a...

Geprc naked gopro 8 TBS ND filter holder
thingiverse

I use it on GEPRC Cinelog 35, but I would not recommend it using on 5" or larger freestyle/racing/long range quads. !!!Update. had several harder crashes last weekend, so it felt off gopro. Printed using Fyberlogy fiberflex 40D filament. But...

BN-180 GPS support GEPRC Cinepro 4K CIGNET
cults3d

Soporte para GPS en GEPRC Cinepro 4K

BN-180 GPS support GEPRC Cinepro 4K CIGNET
cults3d

GPS Support in GEPRC Cinepro 4K

BN-180 GPS support GEPRC Cinepro 4K CIGNET
thingiverse

Soporte para GPS en GEPRC Cinepro 4K

GEPRC Tiny Go frame and canopy for Caddx Loris 4k
thingiverse

... Loris 4k board. (25.5mm x 25.5mm) Combined risers into canopy legs. Added more material around FPV camera mounting holes. Frame: Added more support around mounting posts. Added a solid area in between two ducts that were weak. ...

GoPro Hero 8 TBS ND Filter Cap GepRC Mark4 FPV
thingiverse

Inspired by https://www.thingiverse.com/thing:3929524 Frame: GepRC Mark 4 GoPro: Hero 8 Camera Angle: 25° Since the Lense is slidly further back i had to make the cap design more slim so it is not visible in the video. ... The angle is 25°

GEPRC Baby crocodile / SMO 4K insta 360 support/mount
thingiverse

Hello, This is a mount for the GEPRC Baby Crocodile and the SMO 4k from insta360. The tilt of the camera is : 25°. You should print it horizontaly to spend less filament. ... If you want to tip, thank or help me, here is my paypal :...