gerber holster 3d models
4334 3d models found related to gerber holster.thingiverse
This is a holster for Gerber DIME. A tiny, almost key chain like, super useful multi-tool. __I highly suggest printing the retaining wall version and in ABS__ I have printed this in PLA before which was perhaps more rigid, but couldn't be...
thingiverse
I wanted a slightly different version of the "Gerber Dime multi-tool holder" so I remodeled it in SW and changed it to a spring clip. ...I carry this with me in my MTB tools and this secures the tool perfectly in my bag.
thingiverse
Customized version of http://www.thingiverse.com/thing:335122 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=335122
thingiverse
UPDATE: This version is now deprecated, and is not worth printing! A completely redesigned and improved version is now available:http://www.thingiverse.com/thing:927363 I will leave this version up for posterity, but it never worked well, so it is...
thingiverse
A two-piece holster for you Gerber Center-Drive multi-tool. ...Clips conveniently to your belt and keeps your tool within hand's reach.
thingiverse
This is a holster for your Gerber EAB Lite folding utility knife. The knife will fit into the holster from the top or bottom. The pivot will "snap" past the bottom edge and hold the knife in the holster along with the spring clip on the knife...
thingiverse
Simple belt holster for your standard-issue Gerber multitool. Designed to be printable in the vertical position and only require supports within the belt loop portion of the file. I printed mine at 15% infill and it was plenty. ... I do simple...
thingiverse
The design is based on Adam Savage's design he presented at Tested.com, See: http://www.tested.com/art/makers/461173-one-day-builds-adams-custom-multi-tool-belt-holster/ Instructions Made in Catia V5 if you can use this program you are more then...
prusaprinters
Holster for Gerber Center Drive. Mounting methods: Molle 1in by 1.5in Flatback for adding your own mounting system Right-handed I couldn't find a sleek, minimalist 3d printed holster for my CenterDrive online so I threw this together. Yall gotta make...
cults3d
This holster retains the tool with 2 springs that click into 2 round holes on the tool. It will not come out unless you give it a sharp yank. It fits most standard leather belts under 2" in width. If you experience any problems, message me and I...
thingiverse
Sheath/belt holster for the Gerber clutch, these are no longer made sadly but I designed this because I had one lying around and thought it might be nice to have a holster for it. ...
prusaprinters
A two-piece holster for you Gerber Center-Drive multi-tool. Clips conveniently to your belt and keeps your tool within hand's reach.</p><p><i>Updated Version</i></p><p>The latest version has been re-styled to match the Centre-Drive, remove some bulk...
thingiverse
Belt holster for Gerber Multi-Plier 600 Multi-Tool. As used by the Canadian and US Armed Forces. It fits just snug. So far survived a weekend of chasing after my kids outside. Lots of running, jumping, and crawling. Print as-is. Use a brim...
prusaprinters
Holster for this great multi-tool. A couple options depending on your needs and where it'll be mounted.</p> <p>I've added the V2 design for this after completely rebuilding in OnShape.</p> <h3>Print instructions</h3><p>Print as is, using a brim if...
thingiverse
I found when I would sit down in my car it would pop out of the holster. So there are now three versions: Closed (preferred by me), Shield (original), and Minimal (which is just enough to hold it on a belt, but could be pushed out from the bottom). ...
thingiverse
Customized version of http://www.thingiverse.com/thing:335122 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=335122 Instructions Using the following options:...
thingiverse
Belt holster for my Gerber Flik multi tool. Inspired by Adam Savage's multi tool holster. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:335122 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=335122 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:335122 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=335122 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:335122 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=335122 Instructions Using the following options:...
thingiverse
This blade was so insanely handy for stripping coax, I just had to take it to work with me (which is pretty much everywhere) So I made a magnetically retained holster for it. Best suited for 30-35mm wide belts. I suggest you print it...
thingiverse
Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372
grabcad
Gerber Axe. ...(The one that features in Man Vs. Wild). Please note that the Solidworks Part and Assembly file, STEP file, and IGES file are all zipped inside the "Gerber Axe.rar" & "GerberAxe.zip" files.
grabcad
This is a recreation of one of my Gerber Multitools. ...The parts are as close to accurate as I could get with a caliper/micrometer
thingiverse
This is a holster liner for a Gerber Multi-Plier 400 Compact Sport. My fabric holster is very worn out as you can see in the photos. This insert should make it last a bit longer. This would be a good idea to insert into a new holster so it doesn't...