gl inet gl ar150 3d models
5916 3d models found related to gl inet gl ar150.thingiverse
Wall mount for GL-iNet GL-AR150 (and possibly the gl-MT300 series, they look similar) mobile router. For those with antennae or not. Can mount using magnets (5mm x 2mm thick or 3/16" x 1/16" thick), screws or hang from the hook. The USB stick...
grabcad
This is the GL.iNET Router GL-MT300N or the GL-AR150, it is a mini router.The PCB has been modeled using a photo, the ICs placement is on the fly.The copyrights for the non original elements are inside the corresponding files (Thanks for the...
thingiverse
Wall mount for the GL.iNet GL-B1300 AC Router. I printed in Polycarbonate as that was what was in the printer at the time, guessing it would print fine in anything else? ... I used support to ensure the tabs are flat and clean.
thingiverse
Wall holder for GL inet Beryl GL-MT1300 router. Could possibly fit also other similary shaped router models like - Slate AX, Opal, GL-S200. Holders are to be glued to the wall with double side tape like tesa Powerbond. ...
thingiverse
... holder for it, but it is out of stock and the company says that they will not restock it. https://store.gl-inet.com/products/accessories?variant=32121681805406 So I used this picture to create one. It turned out very nice. ...I used regular PLA.
thingiverse
This is a simple Holder for the GL iNet Router. There are no hangers on his back. I have added some addhesive rubber over the Screws to avoid Scratches and the Router fits nicely Strong in the holder. ... If you have some issues with this Model,...
thingiverse
This is a simple cradle/holder for the GL.Inet MUDI modem/hotspot with passthrough holes for screws and access to the USB A and C. ...Useful for van life, particularly in conjunction with my extenral antenna mod
thingiverse
GL.iNet 64xx WiFi router model. This is a quite old model, but I had several lying around... ...See http://www.thingiverse.com/thing:2183378 for an enclosure built with this model...
thingiverse
This is a simple contoured piece that you install two u.FL to SMA Pigtails into and adhere to the top of a GL.Inet MUDI with a small hole drilled in the top to pass the cables through to the modem module inside. Useful van life I'm conjunction with...
thingiverse
... one of these chinese PoE splitters. ...Thus the devices have a significantly higher WAF. --- Deutsch --- Ein Gehäuse für den MT300N (Mango) von GL.Inet und einen der chinesischen PoE-Splitter. Damit haben die Geräte einen deutlich höheren WAF. ...
thingiverse
A bracket to hold my GL-MT1300 using countersunk 6x25mm
prusaprinters
Simple support to stack a ZTE MF920 modem with a GL.inet travel router. Remix from https://www.thingiverse.com/thing:4646535 Print instructionsPrint the side supports with the sides on the printbed. Clean the margin of the round pegs with the tip of...
thingiverse
Mount for the MT300N router on a DINrail. Print rotated with the right-side of the mount on the buildplate. Put a support block between the two diinrail clamps. ...
thingiverse
Custom 6" rack mount components for GL.iNet mt300n v2, USW Flex Mini, Odroid XU4, Google Coral Stick
thingiverse
Holder for ZTE MF920 on top of a GL.inet AR750s Slate portable router. Easy to clip and remove but only works without rubber pads (you can keep them in the front). ...Mine fell out anyway long ago.
thingiverse
Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372
thingiverse
Customized version of https://www.thingiverse.com/thing:3633456 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3633456
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573