glass bed for anet a8 3d models
2355097 3d models found related to glass bed for anet a8.thingiverse
... like more. I removed version 1 because i think it was a failure. I just didn't do enough testing. Version two is already usable but i would download the newest model. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 30
thingiverse
Anet A8 bullone, dado, supporto vetro ad angolo, e rotella regolazione altezza piano from an idea by http://www.thingiverse.com/thing:1949142
thingiverse
Glass Bed Clip for Anet A8 Prusa i3 For 3mm glass
thingiverse
Customized version of http://www.thingiverse.com/thing:1949142 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1949142 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142
thingiverse
I have also made the bracket 1mm higher than the glass, this is to allow for the clips to hold the glass down as the flat edge that holds the glass in place is only 3 mm high. The design relies upon using the bed leveling screws to hold the clip in...
thingiverse
You can get the glass plate on amazon: (where I got mine) https://www.amazon.de/gp/product/B07DSC9TJQ/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1 (should also work)...
prusaprinters
You can get the glass plate on amazon: (where I got mine) https://www.amazon.de/gp/product/B07DSC9TJQ/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1 (should also work)...
thingiverse
This is a holder for the 3mm glass on a 3mm Anet 220mm heated bed. I extended the side walls a little bit, such that it sticks about 0.2mm above the glass, and has holes for a 3mm screw. While the holders alone are pretty snug, it's not quite enough....
thingiverse
... on tall prints. The way I have designed these they also act as a glass holder and spring stand offs. These are a bit different than the model I remixed them from because the anet has a different style bed carriage.Print as is with no supports.
thingiverse
Designed for Anet A6/A8/AM8/BLV converted to 24V with using the hotplate from Anet ET4. 4 mm cork thermal insulation on the bottom of the plate. Based on the FT5 713 Glass Corner project by davebpix https://www.thingiverse.com/thing:2702867 but...
thingiverse
When autolevel sensor mounted in front all goes really perfect except ordinary glass bed clips, it stays on a nozzle way at back edge when autoleveling goes and it can be on a sensor way at front edge when printing. With this holder nozzle and...
thingiverse
Customized version of https://www.thingiverse.com/thing:311665 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=311665
thingiverse
Customized version of https://www.thingiverse.com/thing:311665 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=311665
thingiverse
Customized version of https://www.thingiverse.com/thing:311665 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=311665
thingiverse
Glass Bed holder for Anet A8 (and possibly others). No need to use clamps, nor to cut the corners of the glass panel. Will host various thicknesses. The glass must be cut precisely to the same size of the bed. ... Update: fixed the side for the bolt...
thingiverse
I decided to make my glass bed look more commercial by adding a design to it and I came up with the idea that I could use my printer to make a mask for the underside of the glass and paint a logo on it. I purchased some high temperature spray paint...
thingiverse
Just Print 2 and should be enough, place one in each corner This is a very simple upgrade that I made for the bed to of the printer cuz I was tired to mess with the claps every time I needed to clean the table, and also to hold the glass in place(i...
thingiverse
just a simple way to keep the glass still and flat this is my first ever attempt at making anything works good on my setup let me know if it helps you update made a smaller one for people with thin glass
thingiverse
I liked the design of the clamps by schnuffi but they seemed like they took up too much room under the bed so I made them thinner and printable without supports. The pin was elongated because I immediately stripped them out. ... For smoother action run...
thingiverse
Adapter for the 21.5 x 21.5 cm glass you can buy on Amazon for the Anet A8. You can use just two V3 corners (not home corner) or three V3 corners plus one home corner version. ---- This glasses from amazon seems to have a high tolerance so I've...
thingiverse
Anet a8 bed clips for those who use 4mm thick glass Solidworks included for more customization.
thingiverse
these clamps are intended for use with 20x21x3mm glass beds on anet a8 (or more in general any bed smaller than the anet aluminium hotbed). the aim was to definitely remove the paperclips avoiding noozle collision as much as possible, allow glass...
cults3d
these clamps are intended for use with 20x21x3mm glass beds on anet a8 (or more in general any bed smaller than the anet aluminium hotbed). the aim was to definitely remove the paperclips avoiding noozle collision as much as possible, allow glass...
thingiverse
... pressure after a short while. Use a little double sided tape under the glass corners and adjust the bed level." Simple bed clip for Anet A8 with 3mm glass. Work it on when cold. It will fit. Not sure how long it will last. ...Only done in pla.
thingiverse
... to hold i down. Pin and nut are not modified. You'll need 2 x corner a and 2x corner b. Mount the corners with the higher side pointing to the front/back of your printer. Print Settings Printer: Anet A8 Supports: Yes Resolution: 0.2mm Infill: 40%
thingiverse
Pour ANET A8 : 220mm x 220mm ATTENTION : Certains retours d'impression m'ont indiqués que la pièce peu présenter des erreurs d'ajustement. N'ayant pas rencontré ce problème, je ne peux le corriger. ... Par conséquent, je partage les fichiers *f3d...