glasses arms 3d models

To replace the arms of your glasses ... ...maybe this model can do it (and save you the time to go to the optician) :D</p><p>Print in less than 20 minutes @ 0.15mm</p><p>Remix from “ericsko” tuned with onshape&nbsp;</p>

These are replacement arms for the BenQ 3d glasses that take the batteries (not the rechargeable ones). The original glasses seem to have a bad design where the arms break really easy. I included two versions.. one with pins like the original you...

Fixed my glasses.

Fixed my glasses.

These are replacement arms for the BenQ 3d glasses that take the batteries (not the rechargeable ones). The original glasses seem to have a bad design where the arms break really easy. I included two versions.. one with pins like the original you...

Made these for my Ray-Ban glasses with the model number RX6363. Printed them at 50% infill and they fit well. ...I recommend tapping the screw hole with the existing screw before attempting to put these on the frame.

Glasses arm; for fix the broken parts or to create a variety of trendy colors.

... i've bought Samsung Smart TV with 3d. ...It came with two pair of active glasses. Unfortunetaly, glasses arms has broken very quick. Originals are very easy to break. And there is no possibility to buy extra parts. I made my own version. ...

Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options: word =...

Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options:...

i couldn't find any arms for my glasses so i made my own very simple design

3d printable eye glasses

... print! It features a 2x2mm hole to put the steel hinge in it. I suggest heating the steel hinge for easier insertion and fixing. Cool down rapidly to avoid overheating. The stl is a right arm, just mirror it in the slicer to have a left one instead.

... the subroutine to make a chamfered cube, quoted in the OpenSCAD source code, was issued under that license. To use: set the width and height of the plastic cross section of your broken glasses arm in the `Sunglasses Repair Brace.scad` file. ...

The entire arm looked too finicky for me to attempt printing a replacement, so I just designed and printed a brace to hold the broken piece to the rest. The brace is basically a box, chamfered for comfort, thinnest on the side toward my face, I...

My glasses were very old and both arms broke from the nail side recently. I designed these which can be modified to match whatever glasses are there. They give better look than the original and they hold the arms very well. ...Unfortunately, you need to...

After using this item, the arm length of the glasses will increase slightly, so you need to shorten the arm of the glasses a little. 2. The 3D printing setting 1 layer cannot be greater than 0.2 mm. 3. The specifications of each type of glasses are...

My Son broke his glasses again so I designed and printed these replacement arms. They slide over the nubs where the old one screwed on. I included a drawing with dimensions so you can see if they will work for your glasses. This is only a left...

Replacement arms for a kid's Harry Potter costume. ... One arm went missing, so I modelled this off the other arm. ... Hopefully this is useful for someone.

Simple endoscope mount for a pair of glasses. Uses small rubber bands for adhesion. ...Helpful for recording first-person repair jobs.

# Sleeve to Repair Break in Glasses Arm The arm of my reading glasses broke near the hinge. This project is a simple sleeve used to repair the break. These glasses have black plastic frames. ## Used Parameters for Easy Modification The Arm...

Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options:...

I designed a 3D printed glasses right arm for my friend.

a fix to my cousins glasses, the solidworks file is included so you can edit it for your size head and type of glasses

Customized version of https://www.thingiverse.com/thing:1653805 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1653805

I broke my 2 G15-DLP Arm (3d glasses), so I create new ones. here they are. maybe a bit small for large head, they fit my girlfriend and I. ...Print Settings Printer: discovery200 Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 40% Notes: they must...

Once it fit, I decided to make it into a customizer, in case other people ever needed to quickly make a replacement temple for a pair of glasses. ...I used a bend module that I found to add a little curve and match the original temple a little better.

Customized version of http://www.thingiverse.com/thing:1653805  

Customized version of http://www.thingiverse.com/thing:1653805 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1653805 Instructions Using the following options:...

... left hand side. Instructions I used PLA, when it had finished being printed I placed it in water just off the boil, for about 30 seconds, when you remove it you can hold the arm in your hands and tweak the shape to achieve the appropriate curves.