glock picatinny rail 3d models

rail risers that's lets face it are way too long for 99% of applications. ...if you are the 1% you are welcome.

it's a Mlok rail so you will need to get your self some of the M-lok bolts and nuts to complete it. ... and print this solid.

Hardest part is lining up the guide rails on each side, try using the spacers attached to each end of rail guide to work out the width and the primer attached to the metal hook to judge the height. Then tape it to the blaster to secure it and poke a...

I used M5x0,5 for mounting (JG 608) Short rail: http://www.thingiverse.com/thing:2095271 Standard version: http://www.thingiverse.com/thing:2053074 Another version: http://www.thingiverse.com/thing:2090887 Print Settings Printer: ctc Rafts: Doesn't...

I designed a custom rail for my Elite Alpha Trooper, featuring precision-cut holes that securely accommodate standard Nerf screws or countersink-fit M3 screws. ...To ensure successful printing, I recommend orienting the model upright and adding supports...

I used M5x0,5 for mounting (JG 608) Long rail: http://www.thingiverse.com/thing:2095264 Standard version: http://www.thingiverse.com/thing:2053075 Another version: http://www.thingiverse.com/thing:2090888 Print Settings Printer: ctc Rafts: Doesn't...

Short rail model available here: http://www.thingiverse.com/thing:2090888 Standard version can be found at: http://www.thingiverse.com/thing:2053074 Print Settings Printer: ctc Rafts: Does not matter Supports: Does not matter Resolution: 0.2 Infill:...

Just a simple modification of another to make it more reliable to print for my printer, and pulling the sides back so it smoothly fits right against the cap on the Nerf MA40 Fits very snug on mine, be careful that you don't print it slightly small...

Slides into the rail on both sides of the Steyr EVO10 barrel rail. The spring construction will take care of a fixed mounted position. The screw (hex) used is a M3x35mm, and uses a M3 nut which slides in the front part. ... Perfect for training...

... platform. ...Then just replace the original rails. You also need a longer screw to make the rear rail stable if Ur sight is heavy. if you use iron sight or you can choose to glue it on the top of your SLAB. ... 打印提示：开启支撑到平台并且躺着打，替换原有导轨，不够稳固可以换一根更长的M3螺丝

This is a Weaver 3/8" rail to picatinny rail adapter I designed to go on top of my Marlin Model 60. ...Tight fit to the weaver rail, also has hole to allow the use of a M3 bolt to act as a set screw.

I had best results printing vertically with a brim, but, that takes significantly longer. ... Acceptable prints were made by using supports from print bed only and printing with the rail side on the bed.15% infill.15 layer height2 Perimeters

I adjusted the rail's dimensions to meet the standard requirements by enlarging it from its original narrow width of 19.16 millimeters, ensuring a snug fit with standard parts that measure 21.02 millimeters.

Remix of the original rail cover. Only 2 rungs shorter. May be better suited for 14.5 inch M4s. For Airsoft, or real steel. I suggest printing with TPU plastic. ... I didnt need supports but its possible

I built a versatile rail mount that's compatible with the Nerf Alphapoint. ...All you require is two M3x16 screws along with a nut to secure it in place.

Compatible with Picatinny Foregrips. The connection between the Pumpgrip and the Slide is made out of Ø 2mm TIG welding filler rod. For dimensions check the Photo. If the press fit of the Ø 2mm rod in the printed part is not enough than you can...

... anyway. I was struggling with scopes on my Caliburn, always tilting and wobbling, so I revised the spreader to extend the p-rail. ... My plan is to mount any sight or scope as far forward as possible to engage both the spreader and the top p-rails.

Short rail available at http://www.thingiverse.com/thing:2053075 and grip available at http://www.thingiverse.com/thing:2000846. Print Settings: Printer - CTC Bizer Dual; Rafts - Doesn't Matter; Supports - Doesn't Matter; Resolution - 0.2; Infill -...

Many of the designs on here for mounting a rail on the 1377 are rather imperfect, rely on disassembly of the pistol, have model errors, are low resolution, or incorrect dimensions. This solves the issue for me. It is 54.75mm long as that was the...

The original was missing holes on one end so fixed that, I also added pockets to the sides to capture the bolts used to secure the riser to the rail. 5mm x 30mm screws with a nut works to secure the part. Or similarly sized machine screw and nut....

Check out these designs: a short rail at http://www.thingiverse.com/thing:2095271, a standard version at http://www.thingiverse.com/thing:2053074, and another option at http://www.thingiverse.com/thing:2090887. ... Printer Settings Printer: ctc Rafts:...

This orientation ensures that the weakest points of the design can withstand the anticipated forces exerted by the barrel when pulled from underneath the rail. Printing material: PETG or ABS are ideal choices due to their durability and resistance...

Printer Settings: Printer: Da Vinci 1.0A Rafts: No Supports: Yes Resolution: .2 Infill: 25% Notes: Be sure to use minimal support to simplify the removal from the rail grooves. ... How I Came Up With This Idea: I started by leveraging sigstoat's rail...

For longer rails, visit http://www.thingiverse.com/thing:2095264. Standard and alternative versions are available at http://www.thingiverse.com/thing:2053075 and http://www.thingiverse.com/thing:2090888 respectively. Printer settings include a...

... The design is fully parametric, making it easy to create shorter or longer versions based on your needs. Just let me know what you're looking for and I'll make the necessary modifications. This rail riser requires three 30mm M3 screws to assemble.

This is a universal tri-rail mounting system for every gun enthusiast's go-to bug-killing assault rifle. A precision-fit tapered interior provides a snug hold on smaller barrels, while an optional favorite adhesive ensures a rock-solid connection if...

... Mantis X10 elite on my cabelas bow sight on my Hoyt carbon spyder turbo. ... it orients the mantis in the correct direction with solid connection to the riser. It could be used with any rail mounted accessory that can be side mounted and face forward.

... with a single M3 screw, eliminating any backlash issues. ...It replaces the standard sighting rail, allowing for effortless aiming without the need for a collimator. ...The print process is remarkably smooth, requiring no supports whatsoever.

there are 3 length in file 115.3mm 75.3mm 55.23mm this is 4 side rail for 30mm barrel you can add lots of laser or lights. ...lol parts: 4 pair 3mm screw and nut (5.5mm weight) i am using LCD-DLP with 0.05mm/layer to print

... your bipod to your bottle front instead of mounting it to the plastick bottle cover. ...only fits in combination of using a regulator so that the bottle comes forward 60mm this way you won't be having troubles with a warping rail on top of the gun