golf ball retriever head replacement 3d models
323139 3d models found related to golf ball retriever head replacement.thingiverse
My wife had one of the spring loaded golf ball retrievers. They are pretty clever, but the weak point is where the head is connected to the handle. Of course, it broke. I saved the telescoping handle and decided to make my own head with a stronger...
thingiverse
Simple designed head for a Golf Ball Retriever to catch a ball and get them of the water. The Golfball simply stuck in the hole so you can lift them up. ...Just put the head on a teleskopic bar.
thingiverse
An easy to print attachment for a golf putter for retrieving golf balls. 4mm countersunk screw hole. ...Let me know if you need a different size for the screw/head.
thingiverse
The golf ball grabber for when your ball is out of reach. Attach it to a telescopic pole and retrieve your ball. ... Mounting 12mm diameter fixing screw needed: m4x25mm socket head cap screw + nut print in ABS
thingiverse
This is a golf ball retriever designed to fit into a paint roller long handle attachment using a locking pin. ...Print in PETG or ABS for strength.
youmagine
The golf ball grabber for when your ball is out of reach. Attach it to a telescopic pole and retrieve your ball. ... Mounting 12mm diameter fixing screw needed: m4x25mm socket head cap screw + nut print in ABS Print Settings Printer brand: Wanhao...
thingiverse
Golf Ball Retriever Why replace the entire pole when you’ve only broken the plastic? This design is one of the most common, and in my opinion, the simplest and very best of the golf ball retrievers, but it is easy to snap it off the end of the metal...
cults3d
This Gold Ball retriever end is made to attach to a long pole for reaching golf balls in hard to reach places. ...Use unprinted 1.75 filament as hinge material.
thingiverse
A friend of mine broke his second golf ball retriever and was complaining that it alwas broke in the same spot. I designed and printed a replacement part, with a beefier section where the telescopic handle connects. The tolerance is importans as...
prusaprinters
Golf Ball Retriever made for the putter grip.Need to inject some sort of putty through the grip hole and use a wood screw to secure it once the putty hardens.
prusaprinters
An easy to print attachment for a golf putter for retrieving golf balls.Print flat on its side, works with PLA but a slightly more flexible filament like PLA+/PETG may be even better.4mm countersunk screw hole (customise as needed via tinkercad)
prusaprinters
A friend of mine broke his second golf ball retriever and was complaining that it alwas broke in the same spot. I designed and printed a replacement part, with a beefier section where the telescopic handle connects. The tolerance is importans as it...
thingiverse
Touch free golf ball retriever designed to prevent golfers from reaching inside the hole when retrieving a ball. Printed at 0.3mm layer height for the sake of print speed.The "Stem" file can be inserted in either direction and fits both base parts. ...
myminifactory
Touch free golf ball retriever designed to prevent golfers from reaching inside the hole when retrieving a ball. Printed at 0.3mm layer height for the sake of print speed.The "Stem" file can be inserted in either direction and fits both base parts.
thingiverse
... it breaks near the base. I decided to print it in Polyflex for longer life. The sides of the original were too narrow for Polyflex and it wouldn't retrieve the ball consistently. ...I made the walls thicker so it would work with Polyflex.
thingiverse
Don't lose you golf balls. This is easy and neon yellow looks good in dark water. ...I use hot glue.
prusaprinters
Had some time and had some fun!Will likely need to add some details but only after the Golf courses open :-)Should work with 2.5 x 14mm dowels Based...
thingiverse
I took bochiasson's base and stem v2 and replaced the stem with an iron wire recycled from laundry clothes hanger. ... I reduced the joints diameter to better fit the flagstick, but not to a diameter as small as bochiasson's v3 because it was too small...
thingiverse
Remix of the golf ball retriever so that it can be used in the grip hole of a shaft instead of at the end of a telescopic tube. ...
thingiverse
Golf Ball Retriever for the end of a Putter, this doesn't fit putters with weights in the grip. ... I had to print this with a Brim and Supports but you might be able to print it without supports, I did the Infill at 100%
thingiverse
Golf Ball Retriever - End of Club Ball Retrieval Simple Ball retriever that fits on the grip end of your club. Allows retrieval of Ball from inside the cup with flag in place or can be used to grab a ball that has wandered into a less than desirable...
myminifactory
This is a PVC catapult that will be launching golf balls. ...The head is designed to hold them.
prusaprinters
Disc golf retriever with joint.Needs M5/8mm nut with glue.Remix from https://www.thingiverse.com/thing:4335186
thingiverse
This is a golf disc retriever. When a disc goes in the water, this is suppose to be velcroed to a long stick and then the stick can be used to retrieve the disc. I've been researching which one to get, but figured this would be easy to design and...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_bar_th = 3.2 gopro_captive_protruding_h = 0.5 gopro_primary = triple gopro_bar_screw_head_d = 6.2...
thingiverse
https://www.youtube.com/watch?v=qLQw8j031tM I created this tennis ball retriever so that I wouldn't have to stoop so much when picking up tennis balls when I practice serves. You need a 3" diameter poster tube, wide tape (duct tape, packing tape, or...
myminifactory
Dog : Golden retriever Head Sculpture Portrait File: Formate splits into two pieces. File ready for 3D Print (File clear the work file. ...And ready for 3D printing) OBJ (Merged Dynamesh Decimated Cleanup )STL (Model is STL file format for Printable ) ...
thingiverse
... Fit on tube isn't overly tight as I always intended to glue it on. If you print at 99% it should be tight enough fit but may not support the weight of may tennis balls. ... Printed on Ender 3 25% infill No raft, no supports E-sun PLA+
thingiverse
A clip retrieving Disc Golf disks from water, trees, or brush. Attaches to the end of a telescoping pole for remote retrieval. Instructions The clip will be much more flexible and last longer in PTEG. I used ABS+ with good results though. I...
cults3d
Dog : Golden retriever Head Sculpture Portrait File: Formate splits into two pieces. File ready for 3D Print (File clear the work file. ...And ready for 3D printing) OBJ (Merged Dynamesh Decimated Cleanup ) STL (Model is STL file format for...