gopro 5 mount compatibility 3d models

BOM: Plastic or Aluminum tube 15,5 mm (Hardware store) M5x20 mm Screws and Nuts for the joints or GoPro Screws M5x8 Screws for the revolving joint between the tube adapter and the GoPro mount Used it for some of my other things:...

Nazgul 5" Gopro Hero Mount

Gopro session 5 mount for TBS source one V3 with TBS nd filter

Hi! ... This is a remix of my runcam 5 mount for TBS source One V5 frame, but this time with gopro-type mount :) 26/06/23: redesigned the thing, first version was too wobbly

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_rod_nut_th = 3.6 gopro_bar_th = 3.2 gopro_secondary_what = double gopro_bar_screw_shoulder_th = 4.5...

Other FPV stuff: Alien 5" GoPro mount: https://www.thingiverse.com/thing:5415297 Alien 5" action cam mount: https://www.thingiverse.com/thing:5437367 Alien 5" GPS mount: https://www.thingiverse.com/thing:5437354 Alien 5" Legs:...

If you like it, consider tipping :-) Please also have a look at my other creations for the AOS 5.5 AOS 5.5 Crossfire Immortal T Mount: https://www.thingiverse.com/thing:5248645 AOS 5.5 Caddx Polar Antenna Mount:...

mount

gopro5 mount, fits lanParte stabiliser. ... print with support

Speedybee Master 5 Gopro Mount

Steele 5 gopro session mount.

GoPro Hero 5 session camera mount

Steele 5 gopro session mount (bangood)

GoPro mount for the Emax Hawk 5

Shendrones Tweaker 5" GoPro Session mount printed out of Semiflex. ...

This is a mount for Gopro Session 5 or Runcam 5 Orange with damping.

Lightweight GoPro mount for 5/6/7. Print with TPU, infills 100% print speed 25mms-30mms Must print 100% infills to reinforce the strength of the GoPro screw mounting area. V6 has around .50mm gap between gopro base mount and the gopro mount. ... V6.5...

Mount GoPro Session 4 / 5 - Hammer 5

Better runcam5 mount for gopro mounts.

AOS 3.5 GoPro Mount Just a mix of the 2 designs All credit to original creators

Custom design GoPro mount for Soko 5 frame with 25deg uptilt. Mount it with M3 x 10mm bolts. ...The slot fits 15mm x 210mm long lipo strap.

This is GoPro mount for the Detroit Multirotor 5" True-X and Stretch-X. It bolts down directly on top of the top plate. ...Supports are needed.

Mount GoPro session 5 AP1 For problems or requests please contact the ATTACCO team via email! ... Email: direzione.attacco@gmail.com

It's an adjustabble gopro mount for the steele 5 frame that ii have made for my quad. ...It's work like puzzle pieces.

Holds Samsung Galaxy Note 5 and connects to a GoPro mount. Printed and tested. ...Fit is a little tight but not too bad.

Gopro 7 mount for Steele 5 frame. Perfectly fit the frame and you can add a strap to hold the camera! ...25° inclination!

GoPro Session 5 mount to use with Reelsteady Go on a drone. ...Work in Progress, mainly the base needs to be changed / adapted to your quad.

GoPro session 5 damper mount for suppressing high-frequency noise in gyro-data when use with fpv racing drones. ... -30 deg pitch; Flex plastic & high fill dense preferable.

Added a Go pro mount 25 degres Tilt. ...If the printed tpu, 100 pourcent, was very strong! I just adjuste this gopro mount for the amax Freestyle 5 and may be 5E.

This is a 30° GoPro Mount for the 5" Alien. To mount a GoPro you need a 20mm wide and 300mm long strap. I use the 300mm graphene straps from hobbyking. ...Print Settings Printer: DaVinci 1.0 ...