gopro bar mount 3d models

This is a GoPro bar mount for the clip. You can also print the upper part separated and mount it with a M5 screw. Based on https://www.thingiverse.com/thing:2082169 and https://www.thingiverse.com/thing:3472928 This thing was made with...

Simple go pro mount that used m5 bolts to clamp your GoPro to a bar.

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_th = 3.2 gopro_primary = triple gopro_bar_screw_nut_d = 6.01 gopro_captive_rod_id = 3.8 gopro_rod_nut_th = 3.6 gopro_ext_len = 35...

A year ago, my GoPro camera along with its roll bar mount was stolen. This spring, I bought a new Hero 3 but without the mount. To complete my set, all that was required was a roll bar mount. Here's my straightforward yet robust design for a tube...

Simple go pro mount that used m5 bolts to clamp your GoPro to a bar. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 100% Notes: infill amount is optional, I printed it solid...

I got a cheapy set of gopro accessories and after a while, the handlebar mount broke. I made this one to be more beefy. Print on its side and print solid. requires supports. There are others here, but I like the satisfaction of fully making...

I got a cheapy set of gopro accessories and after a while, the handlebar mount broke. I made this one to be more beefy. Print on its side and print solid. requires supports. There are others here, but I like the satisfaction of fully making something...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 8 gopro_primary = triple gopro_secondary_what = clamp gopro_rod_nut_od = 8.05 gopro_bar_screw_head_d = 6.2 gopro_bar_screw_nut_d...

I recommend printing larger than the bar it's supposed to be mounted on and using some thin rubber material or foam to prevent the mount from rotating/sliding. ... NOTE : I decline all responsibility in case of damage to the objets you mount on this...

GoPro Bike/Bar Mount Print Settings Printer: FF Creator Pro Rafts: Yes Supports: Yes Resolution: 0.20 Infill: 70% Notes: Material - ABS Post-Printing Removing support material was effortless, but rafts were a bit challenging Design Changes Adjusted...

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

To assemble this GoPro camera mount, follow these specifications: gopro_bar_screw_head_d = 6.2, gopro_bar_rod_d = 12.3, gopro_rod_nut_th = 3.6, gopro_bar_gap = 2.4, gopro_bar_screw_d = 3, gopro_bar_th = 3.2, gopro_primary = triple,...

To personalize this design, use options including gopro_secondary_rotated, gopro_bar_screw_head_d, gopro_secondary_what, gopro_bar_screw_shoulder_th, gopro_bar_screw_nut_d, gopro_captive_rod_angle, gopro_bar_screw_d, gopro_bar_gap,...

Customizing options include: gopro_captive_rod_angle = 45; gopro_secondary_what = clamp; gopro_primary = triple; gopro_bar_rod_d = 30.5; gopro_ext_len = 30; gopro_captive_protruding_h = 0.5; gopro_bar_screw_d = 3; gopro_captive_rod_id = 3.8;...

A neat and compact handlebar mount for a GoPro camera. Only a single clamp bolt is used to attach it to the handlebars due to the plastic hinge. This is not designed for (though may survive) repeated installation & removal, since the hinge is fairly...

To create this customized design, specific options were used such as gopro_secondary_what = clamp, gopro_bar_rod_d = 45.5, gopro_captive_rod_angle = 45, gopro_ext_th = 3, gopro_rod_nut_od = 8.05, and more. ...Check out the link to see the final design!

Customized version of https://www.thingiverse.com/thing:3723982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3723982

GoPro Handlebar Mount - Uses 2 off M5 caphead screws to mount to the handle bars. ... Designed for 31.8 mm bars.

The specifications used for this model include a gopro_captive_rod_id of 3.8mm, gopro_rod_nut_th of 3.6mm, gopro_bar_th of 3.2mm, gopro_rod_nut_od of 8.05cm, gopro_bar_screw_d of 5.4cm, gopro_ext_len of 20.7cm, gopro_bar_screw_shoulder_th of 4.5mm,...

The 3D printed Bike Bar Mount has been designed to be 100% 3d printed with no additional hardware needed, just the GoPro. the mount is made to fit a 30mm Bar, but I have included two adaptor rings one so it will fit a 25mm bar and also one for a 20mm...

The 3D printed Bike Bar Mount has been designed to be 100% 3d printed with no additional hardware needed, just the GoPro. the mount is made to fit a 30mm Bar, but I have included two adaptor rings one so it will fit a 25mm bar and also one for a 20mm...

This has a flat bottom to mount on any surface, with 3mm screw. With standard Gopro connector. ... Printer i usedhttps://www.banggood.com/DIY-Creality-CR-10-3D-Printer-300300400mm-Printing-Size-1_75mm-0_4mm-Nozzle-p-1085645.html?p=DG23031123036201501P

... a flat bottom to mount on any surface, with 3mm screw. ... With standard Gopro connector. ... Printer i used https://www.banggood.com/DIY-Creality-CR-10-3D-Printer-300300400mm-Printing-Size-1_75mm-0_4mm-Nozzle-p-1085645.html?p=DG23031123036201501P

A 2-inch bar mount is presented, which incorporates a standard GoPro bar clamp screw and hinge. The hinge point measures 3mm, and a small piece of 3mm threaded rod was used; however, the CAD files are included for customization. Photos lack the acorn...