gopro cage 3d models
34206 3d models found related to gopro cage.thingiverse
Hi this is a model made by myself for my school project, hope you like it! ... Enjoy it!
thingiverse
Gopro mount for the Project 399 frame. ...You'll just need the standard screw that comes with the gopro cage and a lock-nut. ... Print laying on it's side for perfect strength
thingiverse
got bored and created my own gopro cage for the MQC XHD. i love the ones that the mini quad club offers. it has gone thru hell and back. but i wanted to create something with my own idea. granted its not weight conscious at all. ...but its my kinda fun...
thingiverse
Designed this GoPro Cage to replace the original couch that comes with the Epic. No need for a velcro strap. For best results, you will need to file down the sides of the cage a little bit. ...
thingiverse
This cage is for Thronmax MDRILL One Pro You must print PLA 1x gopro_cage_for_mic_cage.stl 2x gopro_cage_for_mic_arm.stl TPU 2x gopro_cage_for_mic_tpu_part.stl
thingiverse
I used this to perform vertical shots with a very small and portable drone by putting the Gopro into time lapse mode before starting. The small piece is for fixing the camera inside of the frame (see photos) using an M2 nut and bolt. My setup: EMAX...
thingiverse
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Lightweight gopro hero 3+ cage for use on a drone, where weight is important.
thingiverse
A Gopro mount that fits on a 41mm diameter roll cage tube (Porsche 996 GT3 mk1 Clubsport)
thingiverse
Made an adapter to attach a bottle cage mount to a GoPro buckle. I originally designed it to carry my speaker on my surfboard using a bicycle bottle cage. ... Hardware: 5mm nut and bolt
thingiverse
This is a Rad Power Bikes GoPro Bottle Cage Mount and should fit any Rad bike.
thingiverse
Pebble steel mount to underside of gopro session cage. ...Mount up-side down on bike for computer and camera.
thingiverse
GoPro Session Cage protection for the Team Mistral AK47 original mount https://www.thingiverse.com/thing:3843199 With protection for the GoPro lens and you can add the TBS Jello Guard ND Filter Link to buy the frame :...
thingiverse
GoPro Hero8 Cage protection for the Team Mistral AK47 original mount https://www.thingiverse.com/thing:3843199 With protection for the GoPro lens and you can add the TBS Jello Guard ND Filter Link to buy the frame :...
thingiverse
http://www.genustech.tv/collections/gopro/products/gopro-cage Cage is designed to protect a Gopro in its waterproof housing, however due to the GoPro's short battery life I always have the battery Back Pack attached. This prevents the aluminum back...
cults3d
Designed to attach a gopro or similar to a 38mm spout in the vehicle cage, no need to place an anti-vibration rubber around the spout Designed for gopro or similar screws. ... Instagram: Panorama.3d
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_bar_th = 3.2 gopro_captive_rod_angle = 45 gopro_secondary_what = clamp gopro_ext_len = 0 gopro_primary = triple...
youmagine
The two circular rings in the back slide over the top plate spacers, while integrated channels in the front allow two zipties to thread through the mount and the frame plate, locking the cage in place; an additional circular nub on the bottom of the...
thingiverse
It comes with two screw holes so you can remove the original Garmin mount on the light and install the light directly into the cage with minimal profile. **Built and tested on a RN1500. You may want to double check the dimension of other models...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_protruding_h = 0.5 gopro_bar_screw_nut_d = 9 gopro_ext_len = 35 gopro_bar_rod_d = 42 gopro_captive_rod_angle = 45 gopro_bar_screw_d...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_bar_th = 3.2 gopro_bar_screw_d = 3 gopro_rod_nut_od = 8.05 gopro_bar_gap = 2.4 gopro_bar_screw_nut_d = 6.01...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 30 gopro_bar_screw_nut_d = 6.01 gopro_bar_screw_d = 3 gopro_rod_nut_th = 3.6 gopro_bar_th = 3.2 gopro_bar_screw_head_d = 6.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_rotated = 1 gopro_captive_protruding_h = 0.5 gopro_rod_nut_od = 8.05 gopro_bar_screw_head_d = 6.2 gopro_bar_gap = 5 gopro_ext_len...
youmagine
With the lens that I used (it came from an old slide projector) my Gopro can focus now on distances between 7cm and 9cm. However, if you build that construction, the lens that you'll use will be certainly a different one than the one I found in my...
thingiverse
Customized version of http://www.thingiverse.com/thing:909819 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=909819
thingiverse
This lens cover goes over the Session frame and protects the lens from scratches and dings. ...I printed it in PET and TPU and it printed great.
thingiverse
My gopro session is mounted on my helmet at the chin level so I needed to have the same angle of the housing when attached to it mount. Print Settings Printer Brand: Ultimaker ...
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
This Gopro Cage is designed to be sleek and minimal. ... It is designed around the Goro hero 6(If im not mistaken) Do not use supports in the mounting holes(If u want to use them) The fit is not perfect, it is a work in progress Finally Enjoy...