gopro for bike 3d models
2246286 3d models found related to gopro for bike.thingiverse
Orientable GoPro holder for bike, based on a ball pivot pressed by a nut. This assembly counts 4 parts and needs 3 M5x20 screws and nuts. ... I recommend printing the parts (except the nut) split in 2 so that you hardly have to use any support.
thingiverse
Orientable GoPro holder for bike, based on a ball pivot pressed by a nut. This assembly counts 4 parts and needs 3 M5x20 screws and nuts. ... I recommend printing the parts (except the nut) split in 2 so that you hardly have to use any support, and...
grabcad
Standard GoPro mount, that could be attached to bike stem. It has internal channel for the cable tie. ...On this mount can be attached GoPro or any other device like this phone holder: Phone holder
prusaprinters
... are headlights out there that already have the GoPro mounting system. For example:Garmin Varia Headlight Olight Front HeadlightThere are also a myriad of other lights out there that have adapters for GoPro mounts.
thingiverse
This is a simple mount for any Gopro or similar. ... I Hope you like and make great shots!
thingiverse
Gopro Handle for Bike Dual Mount This design has not been tested on a bike yet.
thingiverse
A GoPro filming in this location creates great B-roll videos to supplement your biking videos. In addition to the printed bracket, I used 3x standard GoPro thumb screws and 3x hex-nuts that can be pulled from any GoPro mount. Each bike seat and seat...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_bar_screw_d = 3 gopro_rod_nut_od = 8.05 gopro_rod_nut_th = 3.6 gopro_captive_rod_angle = 45 gopro_ext_len...
grabcad
Mount your riding light easily to helmet or bars by using your gopro mount
thingiverse
Put the nuts into corresponding places: on top of the **Pivot** part (for GoPro screw) and into **NutHandle** part, then, optionally fix it inside **NutHandle** with **NutHandleCap** part. ... I would recommend using rubber gaskets (I've used old...
thingiverse
... 4mm plastic clamps to fix this on the helmet. It is recommended to customize the bottom of this thing for your helmet shape - SolidWorks 2017 source file attached. ... Simplify3D factory file attached as well (because some supports are required).
thingiverse
holder for akaso v50 camera for under a garmin head unit using a gopro setup. ...
thingiverse
GoPro Halterung zur Befestigung an der Trinkflaschen Aufnahme
thingiverse
Haven't tested the GoPro mount portion (remix from jolyboy’s GoPro mount for bike, which has many likes and confirmed makes), but this is a remix from Eric Chu's AirTag holder and I can confirm that it fits on my Specialized SL7 and holds an AirTag...
thingiverse
Attaching the camera to a bicycle helmet. ... This will replace the part of the Cateye helmet mount(http://www.amazon.com/dp/B00ARI5YAG) 自転車のヘルメットにカメラを取り付ける為のパーツです。 Cateyeのヘルメットマウント(http://www.amazon.co.jp/dp/B00CDP8E9O) のライト取り付け部分を取り替えて使います。
thingiverse
(Close The Gap -> Hide My Bell) I just needed a small GoPro holder for my mount which I can use with PowerPod on my bike. I found one on Thingiverse, but it was too big and was not looking well. So - ten I designed a new one which is fitting better...
thingiverse
I liked this adapter, but I needed to rotate the mount 90 degrees so that the devices that I mount on the adapter point forward. ...
thingiverse
Gopro mount will support either on 18mm-23mm bike's chainstay or 40mm MTB fork It will clamp with four (4) M5 nut and 30mm length bolt. --- I spent quite a bit to time to come up with this, so your feedback will improve next version. ...
cgtrader
This is 100% printable model. ...It is made for the diameter of 43mm , but feel free to ask for another size. It is made for the M4 screws. You can mount it for example to bike/motorbike schock on the front to have a side view from the camera. ...
thingiverse
Can be used with any bike for cool video from the first person.
prusaprinters
Bottle holder with GoPro style mounting.2 parts can be merged with just pressurefit, glue, or a piece of 1.75mm filament.
prusaprinters
Holder for a GoPro hero 3 I made when I was 14. Meant to be clamped with the handlebars where it is attached to the stem. ...Printed on ender 3 using the cura v4.11 CHEP profiles.</p>
thingiverse
Allows you to mount a bigo bike light on any gopro holder. ... Used with a handlebar support, for example.
prusaprinters
I've also created a GoPro compatible mount for the rails of a bike saddle in order to use it with my SIGMA BLAZE mount (https://www.prusaprinters.org/prints/61869-sigma-blaze-mount-gopro-compatible). ...The mount snaps on top of the rails and can be...
thingiverse
A simple remix to fit a Gopro on a dirt bike helmet. In this case a Nolan helmet but may fit other. ... No support needed when printed.