gopro handlebar 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 32 gopro_secondary_what = clamp gopro_captive_rod_angle = 45 gopro_ext_th = 3 gopro_rod_nut_od = 8.05 gopro_captive_rod_id = 3.8...

Customizable GoPro handlebar mount 2014/05/17 Update: Use raft to get better print result Instructions I printed these parts on MarkerBot Replicator 2X Filament: ABS Infill: 40% Number of Shells: 4 Layer Height: 0.2 Supports: off Raft: on (to get a...

This 31.8 mm GoPro handlebar flat mount is printed in three parts: The clamp top, clamp bottom and flat mount itself. The flat mount is screwed onto the top part with four M2.5 x 12mm countersunk wood screws after inserting the two M4 lock-nuts into...

Support for any model of GoPro for bicycle handlebars between 29 mm and 32 mm in diameter, for greater recording stability, insert a strip of glue / pad between the piece and the handlebars. Installation with two 4mm x 1.5mm flanges and one nut for...

gopro holder to fix on a handlebar or a tube for diameters from 25 to 35 mm approximately the outer part is printed with a rigid filament pla, abs ... ... the interior is printed in tpu to be anti-slip a printed voice it wrong stuck a flat gopro...

GoPro handlebar mount for a Woom 3 kids bike. ...Uses M3x20 bolt with M3 nyloc nut and M5 nylock nut for the GoPro screw.

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

A GoPro connector for the handlebar of a bicycle. The diameter of the handlebar and the length of the arm is customizable. Three M4 screws (DIN 933, 2x16mm & 1x20mm) and self-locking nuts are needed for the handlebar connector. Two M5 screws (DIN...

A simple gopro mount to clamp onto a handlebar. Also includes the FreeCad file. Based on [992068](https://www.thingiverse.com/thing:992068?ref=makexyz). ... EDIT: changed the diameter to 26mm, increased size between gopro mount pieces.

A GoPro connector for the handlebar of a bicycle. The diameter of the handlebar and the length of the arm is customizable. Three M4 screws (DIN 933, 2x16mm & 1x20mm) and self-locking nuts are needed for the handlebar connector. Two M5 screws (DIN...

You can tune the diameter of your bicycle handlebar and if there is a taper the `gopro-race.scad` supports two sizes. The M5 nut is a press fit and should go on the right side of the mount. A piece of foam between the mount and the handlebar helps...

A handlebar mount for your GoPro, meant to interface with all the standard GoPro accessory linkages. It is secured to the handlebar using two M3x14mm metric button head screws and two M3 nylocks (all found at any hardware store). I printed mine with...

My nephew wanted a GoPro mount for his 22mm mountain bike handlebar. I intended to print or remix an existing design, but all I found were the wrong diameter and only included the .stl which is difficult to modify. So I whipped up a quick F360...

Gopro mount for a 35 mm MTB handlebar. I use it with Gopro Hero2, will work with newer generation cameras. Mounts with 2 M3x16 mm socket head screws washers and nuts. Can be ABS,PLA or PET-G, as long as you do not crash. If you do, print another...

Quick release and a normal screw handlebar mount (dual camera)

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 31 gopro_primary = triple gopro_secondary_what = clamp gopro_rod_nut_od = 8.05 gopro_bar_screw_head_d = 6.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 20.7 gopro_bar_th = 3.2 gopro_captive_rod_id = 3.8 gopro_bar_screw_d = 4 gopro_bar_screw_nut_d = 6.01 gopro_bar_gap = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_head_d = 6.2 gopro_secondary_what = clamp gopro_captive_protruding_h = 0.5 gopro_primary = triple gopro_bar_screw_shoulder_th =...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 3 gopro_captive_rod_id = 3.8 gopro_bar_gap = 2.4 gopro_secondary_what = clamp gopro_bar_rod_d = 31 gopro_bar_screw_d = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_rod_nut_od = 8.05 gopro_bar_screw_shoulder_th = 4.5 gopro_bar_screw_d = 3 gopro_rod_nut_th = 3.6 gopro_captive_rod_angle = 45 gopro_ext_len...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_nut_d = 6.01 gopro_ext_th = 3 gopro_bar_screw_d = 3 gopro_bar_screw_shoulder_th = 4.5 gopro_primary = triple...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_primary = triple gopro_bar_screw_nut_d = 7.85 gopro_ext_th = 3 gopro_secondary_rotated = 0...

Gopro support for tubes Ø>20mm. ... Tightening is done with M5x30mm bolts and corresponding nuts.

Designed for 31.8mm handlebars. Uses m3 hardware to mount. ... ***This is intentionally oversized on the bar radius to allow for insertion of a rubber pad to reduce vibration***

rather simple :D use gopro_connector("triple"); gopro_bar_clamp( rod_d= 22, th= 3.2, gap= 1.5, screw_d= 3, screw_head_d= 6.2, screw_nut_d= 6.01, screw_shoulder_th=4.5, screw_reversed=false );

Handlebar plug is designed for alloy drop bars and is approximately the same size as a Lizard Skin bar end plug. The Flat Bar plug is also designed for alloy bars and will fit any bar with a 16 - 18 mm inside diameter. ... ...

... to force applied by the screw. I glued a nylon lock nut (unsure of the size) that fits the standard GoPro screw on one side of the mount. This is the first thing I've uploaded, if you have any suggestions or comment please let me know. ...

I designed these super sturdy 15mm and 22mm bar mounts to be use on any of the standard camera mounts like GoPro, Armor X and Tomtom use on their products. It's a slim but strong design with a flexing compliant hinge, witch has grooves so that 2mm...

I designed these super sturdy 15mm and 22mm bar mounts to be use on any of the standard camera mounts like GoPro, Armor X and Tomtom use on their products. It's a slim but strong design with a flexing compliant hinge, witch has grooves so that 2mm...

GoPro handlebar mount for Giant Contact SLR.