gopro helmet mount extension 3d models
395332 3d models found related to gopro helmet mount extension.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_head_d = 6.2 gopro_rod_nut_th = 3.6 gopro_bar_screw_nut_d = 6.01 gopro_captive_rod_angle = 45 gopro_primary = double...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_head_d = 6.2 gopro_rod_nut_th = 3.6 gopro_bar_screw_nut_d = 6.01 gopro_captive_rod_angle = 45 gopro_primary = double...
thingiverse
Few extensions that can be used with Gopro mounts. ... It is recommended to use infill atleast 50% of higher while printing.
prusaprinters
I designed a GoPro Mount Extension for the Webcam holder from @foorschtbarSo you can use all kind of accessory with GoPro Mount. Could be useful with accessorys like:...
thingiverse
The Hex Nut is a M5x0.8, this threads right onto the GoPro's thumbscrew and a light press into the hex shaped cavity of the extension head. The Dustcap wasn't a requirement and was painstaking to get the fits correct, but it snaps in and can be...
cults3d
this is a simple design, I just need to create a " real " extension" cause sometimes you need to have a middle mount to create a different angle and you need on both sides of the extension the 2 feet instead of 3 feet on one side and 2 in the other !...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_gap = 2.4 gopro_captive_rod_id = 3.8 gopro_bar_screw_head_d = 6.2 gopro_captive_protruding_h = 0.5 gopro_bar_screw_shoulder_th = 4.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_ext_len = 100 gopro_primary = triple gopro_bar_gap = 2.4 gopro_bar_screw_head_d = 6.2 gopro_bar_screw_nut_d = 6.01...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_rod_nut_th = 3.6 gopro_ext_th = 3 gopro_captive_protruding_h = 0.5 gopro_secondary_what = double gopro_bar_rod_d = 31 gopro_primary = triple...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_secondary_what = double gopro_bar_screw_d = 3 gopro_rod_nut_th = 3.6 gopro_ext_len = 30...
pinshape
In this case it helps me use my GoPro Session with this mouth mount I could make it work without it and the setup GoPro sells is just a mess.. The rounded design is useful for the times when your mount can not fully rotate to the position you need...
thingiverse
It's a two pieces extension. Should be fixed together using a 2,5x8 screw (see picture). ...You can use them separately as well.
thingiverse
Gopro helmet camera or light mount. Its follow standard Gopro mount, so it works with any Gopro adapter. ... Attach it to the helmet with nylon straps.
thingiverse
2 GoPro mounts for Off-road helmets, Used with Oneal Sierra Ii helmet. Might be suitable for other large-chin variants. ... Feel free to remix
thingiverse
Gopro support for motorbike helmet mount under visor - designed for scorpion adx but will work for others
thingiverse
This motorcycle helmet GoPro mount was designed for the Scorpion EXO-T510 Full Face Helmet. ... The part can be heated with a heat gun to match the profile of the helmet more closely.
thingiverse
And again to hard on the first try. ... changed the model to make the retainingspring softer. just clip it intoyour helmet and mount your gopro. ... no screws required.
grabcad
A simple design for a helmet mount made for a GoPro. ...Less likely to be knocked out of position when hit.
youmagine
i designed a gopro mount for my helmet that only uses 2 zipties to hold it on, it holds firmly in place and works very well.
thingiverse
This is a custom helmet mount for my Icon Airframe Pro, but it will work on a variety of helmets. The notch is there to allow for clearance of a vent on this particular helmet. I used 3M tape on the curved side, and stuck a GoPro flat mount to the...
thingiverse
Print Settings Printer: Prusa Rafts: No Supports: Yes Resolution: 0.3mm Infill: 40 Notes: Print so the gopro mount is facing up. Post-Printing The helmet mount rail mount is a snug fit, but I suspect specs vary. ...I've err'ed on the side of too snug,...
cults3d
This is an helmet front mount for a GoPro action cam I use a Ty-rap to secure it to the helmet for the knob and nut, I prefer to use M4 instead of the original M5 (It works the same, save weight and the captive nut has more space around) Printed in...
thingiverse
This is an helmet front mount for a GoPro action cam I use a Ty-rap to secure it to the helmet for the knob and nut, I prefer to use M4 instead of the original M5 (It works the same, save weight and the captive nut has more space around) Printed in...