gopro microscope mount 3d models

USB Microscope mount (Gopro like). ...Microscope diameter 33mm

I designed this simple bracket to allow the microscope to connect to a standard GoPro mount so that I could mount it to an overhead or table GoPro mount. A great improvement for the microscope! ... Note that this design uses two threaded inserts, M3...

The original mount from the microscope was not accurate to justify, so i decide to use a worm for adjusting. I was inspired from this microscope hack:http://www.hackerspace-ffm.de/wiki/index.php?title=DIY_Mikroskop 10x and 60x magnify works great...

Instructions For the assembly you need follow hardware: 2 x 8mm about 30cm stheel shaft 1 x M10 about 30cm thread bar 2 x LM8UU linear bearing 3 x M10 nut 2 x M3 20mm 2 x M3 nut Insert one M10 Nut into the microscope mount and one M10 nut into the...

... ...Alternate design is a two piece adapter to mount GoPro Hero4 in housing to a microscope with fit over eyepiece. ...Part A size: 3.0"Dx0.625" Part C size: 2.490"Dx1.06" Part D size: 1.598"Dx1.25"GoPro CAD Model from Graham Baldwin GoPro HERO4 Silver

Alternate design is a two piece adapter to mount GoPro Hero4 in housing to a microscope with fit over eyepiece. ...Part A size: 3.0"Dx0.625" Part C size: 2.490"Dx1.06" Part D size: 1.598"Dx1.25" GoPro CAD Model from Graham Baldwin...

This part grips one of the very inexpensive USB Microscopes, to attach it to a GoPro mount. This is the first step in a project to make a useful video microscope using a $10 camera macro focus rail to provide solid support for the camera. I'm...

Mount stand for USB microscope from ebay. ...I think all of them are the same size.

Allows mounting a 2.25" ring light to a Bausch and Lomb Stereo Zoom microscope with 38mm thread mount.

At the ATX Hackerspace there is a microscope and this mounts to the top port for videoing smd soldering.

Mount stand for USB microscope from ebay. I think all of them are the same size. ... Instructions Printed in ABS.

A mount to attach a camera to a microscope. A clip is used to secure camera-holder to microscope eyepiece. Camera attaches with standard M6 screw with a nut (or in this case a thread cut into a printed dowel). ... This design fits an S3300 Nikon...

Replacement holder for digital microscope

... more updates. ... This is an adapter for the Amscope SAW single-arm microscope stand, for the Hayear 14MP C mount lens. ... Basically, it adapts the approximately 3-inch diameter hole from the stand to the 2-inch diameter hole for the microscope lens.

12mm usb-microscope mount. To check geometry, step / mm (requires a reference scale on the heating plate)... ... Designed for http://www.thingiverse.com/thing:18657 or http://www.thingiverse.com/thing:16208 .

The mount was designed specifically for the Edmund Scientific binocular type microscope. It slips right over the eye pieces. If you don't have an iPhone, you can print just the base mount and use rubber bands to hold your phone/camera on. ...

This c-mount made for an electrical microscope. ... You should prepare a 16mm stand rod and a base; The ring adpter/ lens holder is 32mm; Straight gear combined with holdering ring by 3mm screws; Thank you, hope you like it.

Designed this due to the microscope screen I purchased from Amazon and the amazing Vesa mount that CapTec designed gave me the inspiration for this. You just need to purchase 6 x M5 bolts measuring 25mm for the Vesa mount and 2 x M5 bolts measuring...

This is a simple mount for my soldering microscope so it can be attached to a (3/8 inch screw) articulated microphone stand to provide some freedom of movement. ... (The screw thread size on the part isn't perfect, but it does the job pretty well) ...

This is designed to mount my G600 LCD Microscope to an articulating arm (like a desk lamp arm). https://ebay.to/2RnbFwp My particular arm is from an O.C White Magnifying lamp. ... The concept is what is important here, you will have to create a...

This is a device to mount a Microsoft lifecam HD-5000 to the eyepiece of a microscope. It includes six adjustment screws to allow for perfect alignment. I used springs between the CameraMountTop and CameraMountBottom so the camera can be tilted using...

This is a device to mount a Microsoft lifecam HD-5000 to the eyepiece of a microscope. It includes six adjustment screws to allow for perfect alignment. I used springs between the CameraMountTop and CameraMountBottom so the camera can be tilted...

This is a mount for cheap USB microscopes. It allows you to use it on tripods and magic arms, for better positioning and framing. Bolts and nuts are all M3. ...Except the bigger one with is a 1/4" nut machined with a 2mm flange.

A mount for the recommended microscope to run TAMV on a Jubilee printer. Place either a 1" or 7/8" flat washer in the hole so it will stick to your magbed. Also required are (3) thin M3 square nuts and (3) M3x10 button or socket heads. ... Print...

Put a common USB microscope on your TAZ extruder mount for semi-automated optical inspection. Once printed, I heat the clamp gently with hot air and bend the prongs inward for a positive grip on the 'scope. ... https://tinkercad.com/things/3rdiqpTZ5qo

This is a mount for my USB Microscope to attach it to my TS100 soldering iron. Cool to see your own soldering technique up close. It's a bit too heavy to use on everyday soldering. But fun nonetheless. ... See...

USB Microscope Stand, just slide in, thats it. ...Fusion file included

Holder / mount designed keep iPhone 4 (in a case to make it simple and fast slide-in the phone) on a microscope (in my case on Levenhuk school microscope) ... still under development but works already just fine. The photos taken by iP4 are...

This is a replacement adapter for a Hayear electronics microscope with a c mount lens. This part will replace the mount that attaches to the vertical 25mm pole so you can attach the c mount focal adjuster to a monitor arm with a 75mm vesa mount. You...

I've included two shots of the pixels from my HTC Hero taken with this microscope, and a picture of the microscope itself. Instructions This is designed as a parametric OpenSCAD script: You're...