gopro mount for camera stand 1 4 20 thread 3d models

It's sized for 1/4" - 20 ANSI thread. I cut the rods to be about 175mm (~6.9 inches) using a vice and a hack saw. If you only have access to metric rod, you'll need to resize the bracket hole, and change the thread size on the caps (Fusion 360 files...

Having tried several 3D printed 1/4"-20 screws, I discovered that they are frequently quite fragile. This is because they are typically printed vertically, resulting in layers that are easily broken by twisting or pulling forces. In other words, not...

A two piece mount to hold a QHY5III camera with a threaded hole for a standard camera thread screw (1/4" 20tpi). ... Space for two zip ties to secure the halves of the mount, a piece of tape on the inside of the mount can sure up any looseness in fit.

To secure a small camera on my quadcopter's gimbal, I printed a miniature 1/4 UNC threaded mount. This design ensures the bolt will break upon impact, safeguarding the camera from being torn away. ...Print settings include layer height of .15mm, 2...

Since I don't have such a camera, I designed a mount for previous GoPros and SJcam cameras instead. As you can see, the mount also has R9mm antenna mounts built in. I printed it rotated at a 90-degree angle on the X-axis, which minimized the amount...

Camera GoPro mount clip

PRO GoPro Camera Mount

PRO GoPro Camera Mount

Adapter CS-C-M12 mount for 3D-printing (SLA, FDM). ...The adapter can help to mount different lenses with M12 installation on Raspberry Pi 4 High-quality camera with C/CS mount.

I'm in the process of building a super-8 / 8mm film scanner as the current products available today are dismal, poor quality and super-high-maintenance.I'm using a raspberry pi 3 B+, a Raspberry Pi 8 megapixel CSI camera, with its lens removed, and...

If you are using the hard plastic GoPro style mount then use the 'full width' version for a good fit. If you are using something like PTU or similar 3D printed bracket that this will fit into then the other version has slightly thinner pieces that...

This 20mm water pipe camera collar boasts a standard 1/4 inch camera mount. The collar on the pipe provides sufficient tension to keep gravity at bay, but still allows for easy hand movement. It is used in the A2 lightbox corelines. Check out this...

This is a mount for a Samsung Flip 3 to fit onto a tripod. ...It has a standard 1/4 thread. ...I use it for my computer's webcam.

This is an adapter designed to fit a hotshue mount into a mic stand or a camera tripod, depending on the size of the thread, you have two files to choose.

Bed Cam Mount for BLV MGN Cube - Remixed Design Mounts GoPro and SJCAM Cameras.

This is a remix of https://www.thingiverse.com/thing:2214196 I added 2 holes so you can fix you GoPro Session

Use your Gopro mounts with a standard camera that has a tripod mount. I made this so I could use my camcorder with all my GoPro mounts. Instructions You will need a 1/4-20 hex head bolt 1/2" long and a 1/4-20 nut. Print one of each of the 2 parts.

This is a mount designed for small FPV cameras with a resolution of 600tvl and CMOS technology, available from Banggood at https://www.banggood.com/600TVL-8_0MP-14-2_8mm-CMOS-FPV-170-Degree-Wide-Anlge-Lens-Camera-PALNTSC-p-984345.html. The...

A multiple node (3 or 5) stand adapter that connects a standard US threaded microphone stand to several standard 1/4" 20 TPI camera thread mounts on moveable arms. Requires threaded thumbscrews (I use 1/2" long screws) and a microphone stand, but...

... Webcam, available on Amazon, which clones the functionality of a Pi Camera. ...It can be attached to any tripod thread measuring 1/4 inch in diameter.\r\n\r\nCaution: Compatibility with the genuine Pi Camera is unverified and may result in a poor fit.

Mostly because they hold sentimental value.Made a mount that is connected to the camera with a 1/4 inch screw and uses two 2.5mm screws to mount them to the wall.It was designed for the body only, but a small lens attached to the body should be...

Just a simple Camera mount with Gopro mount support added

After the file has finished printing, a 1/4"-20 heat-set insert that is precisely 0.5" long will need to be threaded into the large hole at the bottom of the mount. The printed hinge was secured to the camera with a sturdy M3 x 20 mm screw, which...

This is a custom collar designed specifically for the standard 1/4-20 tripod mount nut. The nut fits snugly into the middle and can be easily secured or released with a simple twist of the fingers. ...I created this design as part of a DIY project to...

Same as the original but I integrated the 1/4 tripod thread into the design, so need need to find a nut. It's not that easy to pick up imperial nuts in the UK and Europe. ... I use this mounted to a static tripod that watches my 3D printer.

The Basler Ace Mounting Plate is designed to perfectly fit the 1/4'' mounting requirements of various Basler models, including the highly sought-after acA2500-14gm. This versatile adapter plate can be effortlessly utilized with other models within...

GoPro Camera Mount for Small Format Cameras with 27mm Pin Holes.

Camera support for universal use includes the http://www.banggood.com/600TVL-8.0MP-14.2.8mm-CMOS-FPV-170-Degree-Wide-Angle-Lens-Camera-PAL-NTSC-product.html link, or alternatively, the...

To assemble, insert a nut into the socket of each end, followed by placing nuts onto the threaded ends and running them down to make space for the rod end. Screw the ends on and jam the nuts against the ends, then apply locktite if desired. Finally,...

This was designed exclusively for the 3DR Solo, allowing you to attach any camera featuring a standard 1/4" tripod mount underneath. The hole is deliberately offset to position a Sony a5100 perfectly once mounted. It also accommodates a variety of...