gopro mount for camera stand 1 4 20 thread 3d models

... Spyder Pod Printable, which can be securely attached with ease. ...It's highly recommended to print this sturdy attachment as thick as possible to prevent any loss of your GoPro camera, using at least three shells and 50% infill for optimal stability.

... tripod attachment point for Sergey_77's camera adapter. ...The thread in the original was the wrong size for my needs, so this is just a resizing to the 20-1/4 thread size needed for typical tripod posts found in the US, or at least in my house. ...

A standard steel 1/4-20 x 1" bolt is much stronger and easy to turn than the printed part. This knob re-mix accepts a matching 1/4-20 nut. Now the arm is easier to adjust at a glance, will accept much higher loads and go to longer lengths without...

This adaptor replaces the base part of the USB microscope so that it can be mounted on a section on 1/4-20 all thread rod.

Very basic design for mounting anything with a 1/4" BPS thread to a standard 3D printer stepper motor. I used it to attach some knockoff Loc-Line that I then clipped a raspberry pi camera on the end. The version with the holes in both directions is...

This can be used to mount a 3/8" camera onto the more common 1/4-20 UNC tripod thread. Alternatively, you can use it as a way to get a high quality 1/4-20 thread into a model printed at lower resolution, or printed with the thread on its side. I've...

This is a versatile C-Mount adapter for a high-definition USB camera module from ELP, available at http://www.elpcctv.com/mi5100-5mp-usb-camera-module-usb20-aptina-125inch-color-cmos-sensor-100degree-lens-p-221.html To use this adapter, you must...

I redesigned the camera socket from scratch, embedding a short 1/4-20 hex head bolt into a groove instead of using the 1/4-20 threaded stud printed at the top of the original design. I created a custom adapter for the C920 since I no longer have...

... store. ...It provides extra grip for the camera inside the case, making it impossible for it to fall out due to being blocked by the bottom bolt on the case. A customized version of http://www.thingiverse.com/thing:193647 Created with Customizer!

1/4" Camera Mount Screw

1/4" Camera Mount Screw

This mount seamlessly swaps out for the standard Asus Xtion Pro Live desktop stand, allowing users to instantly convert it into a tripod-ready adapter. ...By simply screwing the Xtion onto any standard tripod featuring a 1/4" 20 screw, users can unlock...

Swiftly attach your GoPro HD waterproof housing to a regular tripod with these simple steps. ...First, insert the 1/4-inch 20 nut into its designated spot. ...Then, secure it onto the tripod and you're ready to capture stunning footage!

Finger-tightening small captive nut knob with a 1/4 inch 20 thread.

I aimed to attach some photography lighting to a standard camera tripod, but lacked the correct-sized nut. ...To overcome this challenge, I repurposed a larger dial and adapted it for easy hand-tightening.

I needed to attach some photography lighting to a standard camera tripod, but lacked a fitting nut. ...So, I modified this nut by combining it with a larger dial, allowing for secure hand tightening.

This is an adapter that makes a standard 1/4-20 male thread compatible with a 3/8-16 thread. I recently purchased a Rode VideoMic Micro equipped with a lyre suspension mount, but unfortunately, it wouldn't fit on my tripods. ...To resolve this issue, I...

Smartphone Holder for GoPro / Actioncam mount or 1/4 inch camera tripod (in the making) thread.For phone with a width between 61mm and 87mm.Maximum depth of 10.5mm.  No Support needed.Printed with 20% infill.  

Remixed to have a longer screw and a full thread on one side. Meant to be printed this way. ...

A fastening device, such as a screw, can securely attach accessories like a tripod to the bottom of cameras, including models like the Canon EOS 650D.

I remixed https://www.thingiverse.com/thing:4178838 resin mixer to add a 1/4" - 20 thread to the top. Below the thread should have enough room for some glue to secure the mixer to the threaded rod. ... I printed and tested it myself and it assembled...

Nothing fancy, just a picatinny - to - 1/4-20 thread adapter. Screw it onto your tripod plate, put your scope mount or attachment onto the rail and off you go. The thread is sturdy enough to hold the adapter very tightly, provided it's printed well...

Brass Knuckles Style Camera Grip with standard 1/4-20 Bolt Mount Print instructionsPrint using fast 0.3mm draft mode with 5% infill, two shells, no supports or raft.

This mount was designed for any camera with the regular 1/4-20 screw size. I had an adapter that I removed the screw from but you can use a 3D printed screw, the one in the link below from stylesuxx should work fine plus you can edit and make it...

... I made in much smaller for those who are making small batches of resin. ... There is a 1/4"-20 thread on the top, and enough room below for glue. ...I printed it, and it assembled well, I have not mixed with it yet.

Reimagined the original design with three 5mm width slots, a built-in 3D printed 1/4" coarse threaded base, as well as an easy-turning thumb collar to go over the bolt + a cap for the threads to not damage the underside of my desk. Maximum desk...

Mounting your GoPro HD Waterproof Case is now an effortless task that can be accomplished in no time. ...Simply attach the device to any standard tripod and start capturing life's unforgettable moments with crystal-clear clarity.

I used the 1/4 - 20 screw model combined with the components of the articulating raspberry pi camera mount to create an adapter to end mount a screw-type webcam.

This bracket can be used for mini cameras and other devices with 1/4" threads. It is designed to mount a small camera by screwing it to a wall or a pillar for fixed-point observation. Requires M6x25mm bolts and nuts. The long bolt in the photo...

FINALLY a standard 1/4" mount for your Beagle Camera / 3D Printer Controller. If you have a standard 1/4" screw mount this will screw right into it, allowing you to put your Beagle right on top. The two pegs at the top of the mount - plug right in...