gopro seatpost mount 3d models
355950 3d models found related to gopro seatpost mount.thingiverse
This is a Gopro seatpost mount for different diameters. ...Use zip ties.
thingiverse
Mounted with zip tie. This design will fit posts from 28 until 32 mm. ... I printed this without support with only helper discs.
cults3d
Mounted with zip tie. This design will fit posts from 28 until 32 mm. ... I printed this without support with only helper discs.
youmagine
A GoPro camera mount for the small diameter Cannondale Synapse 25.4 mm seatpost. Uses two 6/32 x 1/2 in screws and nuts to secure to the seatpost and a standard GoPro nut and thumb screw for the camera attachment point.Printed with the following...
thingiverse
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
GoPro postseat mount for diameter 31mm. The metric screw M5 space I designed with a 2,75 degree angle - it should stay there for ever. If you need another diameter - would be possible. Enjoy - take some good shots! would be nice to see some good...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_nut_d = 6.01 gopro_ext_th = 3 gopro_bar_screw_d = 3 gopro_bar_screw_shoulder_th = 4.5 gopro_primary = triple...
thingiverse
Bolts now mount back to front to make installation on a bicycle seat post easier. Edited with FreeCAD to tilt the extension arm 17°. The tilt allows a camera to mount above or below without any interference. Will even work with bigger cameras like...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_primary = triple gopro_bar_screw_shoulder_th = 4.5 gopro_bar_screw_d = 3.5 gopro_bar_rod_d = 32 gopro_bar_th = 3.5 gopro_bar_gap = 2.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 4 gopro_captive_protruding_h = 0.5 gopro_bar_screw_d = 3 gopro_captive_rod_angle = 45 gopro_captive_rod_id = 3.8 gopro_bar_rod_d =...
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_rod_nut_th = 3.6 gopro_captive_protruding_h = 0.5 gopro_secondary_rotated = 0 gopro_bar_th = 3.2 gopro_bar_screw_nut_d = 6.01...
thingiverse
This is a mount designed to clamp around a 27.2mm bicycle seatpost to hold a GoPro camera. The camera points toward the back of the bicycle to capture the rear view. ...Additional parts required included (2) M4 Cap Screws, (3) M4 nuts, and (1) M4...
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/96nsZTNejJ2 Print Settings Supports: No
thingiverse
This is a replacement seatpost mount for a niterider Solas USB taillight. My original mount broke, and I needed a replacement. The clamp is intended for larger seatposts (30.9mm) but will fit smaller posts with rubber shims. ... Hardware needed: M3 x...
thingiverse
Pulled dimensions off of the PDW bindle seatpost mount hardware. Interestingly enough, the pieces are in fact not the same width, by about 1 mm. I preserved this irregularity. I included scans of the actual pieces to try & match other dimensions.
thingiverse
... the scad file with a tab to make it removable with those wedge tension clip things. Instructions For better curves, print the seatpost mount with close support. ...The hinge is a bit of wire clothes hanger, ideally grease it up and press it in.
thingiverse
Update: I've added a double bolt version, which secures the bicycle pump with a bolt, similar to the way you mount this holder to the seatpost. This design is 100% secure. This compact and easy to print bicycle pump holder can be mounted to your...
youmagine
Update: I've added a double bolt version, which secures the bicycle pump with a bolt, similar to the way you mount this holder to the seatpost. This design is 100% secure. This compact and easy to print bicycle pump holder can be mounted to your...
myminifactory
Update: I've added a double bolt version, which secures the bicycle pump with a bolt, similar to the way you mount this holder to the seatpost. This design is 100% secure. This compact and easy to print bicycle pump holder can be mounted to your...
pinshape
Update: I've added a double bolt version, which secures the bicycle pump with a bolt, similar to the way you mount this holder to the seatpost. This design is 100% secure. This compact and easy to print bicycle pump holder can be mounted to your...
prusaprinters
It doesn't cost you anything extra, but helps me out a lot :) The links in this post are affiliate links Print instructionsCategory: Sport & Outdoors Summary Update: I've added a double bolt version, which secures the bicycle pump with a bolt,...
thingiverse
A mount for the proprietary aero seatposts on Felt's AR series. Print both the nutted & non-nutted STLs. Never printed/tested personally. Full description from Felt's website: Felt Vibration Reducing Aero Road flip position UHC carbon fiber w/ 3T...
prusaprinters
A mount for the proprietary aero seatposts on Felt's AR series. Print both the nutted & non-nutted STLs. Never printed/tested personally. Full description from Felt's website: Felt Vibration Reducing Aero Road flip position UHC carbon fiber w/ 3T...
thingiverse
Make sure the screws you use to bolt the puck in place aren't too long so it scratches your Seatpost. You can modify the design to use threaded inserts but I didn't have any on hand. Let me know if I should modify and reupload a design with...
thingiverse
a mount for an ebikeling (or similar) ebike controller to attach to a bicycle seatpost using zip-ties used in this project: https://youtu.be/2umTe2oBxts
thingiverse
garmin varia seatpost mount wedge allows use of garmin mounts included with edge530 for varia Rtl515. 27.2mm seat post. ...print on symmetric flat face on plate, no supports
thingiverse
... ...This is the more Advanced Solution. USE TWO MOUNTS! Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: Dosent matter Infill: 20% Post-Printing You could use 10x2MM vercrostraps to strap your box at the mountage, same at the seatpost.
cults3d
Received my Tailfin Aeropack today and figured out that the seatpost clamp was too close to the saddle in order to open the bag. ...Made an adaptor quickly which solves the issue.