gosky scope cam adapter 3d models
138159 3d models found related to gosky scope cam adapter.thingiverse
This design has two parts to it; the scope cam mount (that sticks to the camera) and the scope cam adapter (that slides on to the scope). I used a action camera that is able to record in 720p 120fps and has 4x digital zoom. However this is not...
cults3d
This design has two parts to it; the scope cam mount (that sticks to the camera) and the scope cam adapter (that slides on to the scope). I used a action camera that is able to record in 720p 120fps and has 4x digital zoom. However this is not...
thingiverse
Customisable scope adapter for digital night vision add-on. ... Converts the eye piece of a scope so you can glue it to some 40mm abs waste pipe therefore this should be printed in abs.
thingiverse
Adaptor to mount a Galaxy S7 case to my spotting scope. ...Phone case will be attached by Neodymium magnets This adapter was designed for a single scope application, not likely usable for anything else.
thingiverse
For use on a scopes with 42mm parallax knob (Nikko Stirling Diamond). ... For the bolt join use an M3 hex screw and bolt You can get this printed with high quality petg/carbon filament from here : https://ebay.us/BlvSd2 ...
thingiverse
https://youtu.be/hA66CG-PGGA Gopro 5-7 fit in this angled reflector scope cam: https://www.thingiverse.com/thing:2988760 The connector fits them to this scope:...
thingiverse
As material, you need : - A Mobius 2 action cam, with its long range lens - A longer 24p flex cable (mine is 20.1 [cm] long) - A x50 opening scope, threaded on front - A cylinder battery bank, based on 18650 battery (optional) - Some 2.5 [mm]...
thingiverse
This adapter will turn your cheap finder scope into polar alignment scope for Celestron CG-5 mount. I used 10$ Seben 5x24 [http://tiny.cc/7ofaly] finder scope purchased from ebay for this project. Remark: I made a 1,5 cm shorter print of this...
thingiverse
this scope adapter fits snuggly onto a 2 inch diameter scope eyepiece! Interested in having Product Development, R&D, or Prototyping work done? ...Check out our website with all of our services at www.Createcafe.ca
thingiverse
A quick and handy adapter to use your 30mm scope accessories on your 25mm scope. Shown in the picture is a 30mm bubble level mounted on my 25mm scope. ... PRINT TWO copies, one set for each side - place the larger side on the bed.
thingiverse
This adapter screws on to the threads on the scope, and allows anything that takes 49mm filters to be attached. Other thread sizes could be adapted to 49mm or this could be remixed for different sizes. After using this, I came to the realization...
grabcad
Just the basic envelope of the thing, don't need to get overly anal retentive and make it look like the exact thing with all the bells buttons and needless features.This will be made from HDPE because it only needs to hold the camera fixed in...
thingiverse
Microsoft LifeCam or StudioCam, ...) to a spotting or rifle scope (e.g. Bushnell, ACOG, Schmidt & Bender 5-25/3-27, ...). Or customize to fit your own equipment. Instructions Purposely slightly...
thingiverse
OpenSCAD designs for digi-scoping with a Pixel 3 to a Meade binocular, a Vortex spotting scope and an inexpensive microscope.
thingiverse
This adapter mounts a 1/3 in camera to most scopes. The monitor and IR flashlight then allow you to see in the dark. Print Settings Printer: Wanhao Duplicator i3 ...
thingiverse
Customized version of http://www.thingiverse.com/thing:266273 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=266273 Instructions Using the following options:...
thingiverse
I remade the thumb screws with a bit of knurling which leaves the adapter smaller to pack and access when I want to place on my binos or spotting scope. Uses: *one M4 nut in the base *one M4 x 13mm Philips screws. One gets placed in the...
thingiverse
Lefty9's cam housing: https://www.thingiverse.com/thing:2380562 I like the design of Lefty9's cam housing for the TX03, it indestructible, but I don't really like the TX03 (lack of OSD), so I have created an adapter for smaller AIOs. Print it in a...
prusaprinters
I've created this to mount both my lpvo scope and my reddot to my airsoft. It should work with scopes that have a 30mm tube. M5 Screws are used to screw both halves together.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 50 pipe_outside_diameter = 43 scope_dia = 42 pipe_inside_diameter = 40
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 30 scope_dia = 90 pipe_outside_diameter = 40 pipe_inside_diameter = 34
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: insert_length = 40 scope_dia = 45 pipe_outside_diameter = 43 pipe_inside_diameter = 40
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: pipe_outside_diameter = 5 insert_length = 40 scope_dia = 35 pipe_inside_diameter = 35
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Instructions Using the following options: scope_dia = 42 pipe_outside_diameter = 43 pipe_inside_diameter = 30 insert_length = 50
thingiverse
No supports. ...0.1mm layer height. No bed adhesion. Made for the monstrum lpvo mount and adapted to fit 1" scopes into it.
thingiverse
dovetail adapter for the williams otpics ZenithStar 61 telescope and the ZWO 30 mm guidescope
thingiverse
Small picatinny rail scope ring mount to attach a cheap red dot (https://www.amazon.com/dp/B00A36MKUO) to a cheap compact 3x-9x scope (https://www.amazon.com/CVLIFE-Compact-Crosshair-Reticle-Shooting/dp/B073QM8FP9/) or even cheaper full sized 40mm...