goto dobsonian telescopes 3d models
6266 3d models found related to goto dobsonian telescopes.thingiverse
Automate your base level Orion Dobsonian Telescope using 3D Printed Parts, Belts, and motors. See Bill of Material for a list of parts. This list is not completely comprehensive, but hits the major components. The Electronics consists of a...
thingiverse
Thanks to ProsperGuy, I was able to convert my Sky-Watcher 200P 8" Dobsonian to GoTo using OnStep. Files have been modded to fit the 200P dob. ...The rest of the required files are found on his thingy here: https://www.thingiverse.com/thing:3942813
thingiverse
Is a mix of a frog and a molecule of water with a body in the form of a drop (Gota=Goto).Goto is a bioindicator for water and environment purity. It can be printed in any color. Instructions I used...
thingiverse
It uses components available in any hardware store, a set of two telescope mirrors and some 3d printed pieces. F=750mm D=150mm F/D=5 This was a 2020 summer project, it took me a lot of time. I do not recomment you to use this design (it takes...
sketchfab
A Newtonian telescope on a Dobsonian mount, inspired by the Orion XT8.
thingiverse
These are parts for mounting two NEMA17 drives on 10" Skywatcher dobsonian telescope.
grabcad
John Dobson was an amateur Astronomy who is best known for the Dobsonian Telescope which was a portable, and low cost Newtonian reflector telescope. He gave public lectures, in order to spread awareness for Astronomy as a whole. In 2018 I was gifted...
thingiverse
This thing is a 3D printed Dobsonian telescope designed for an 8" primary mirror with a focal length of 48". The optical tube assembly consists of aluminum extrusions attached with 3D printed ribs designed for standard hardware and covered with...
thingiverse
This is another design for the altitude bearing of a Dobsonian telescope, an improvement over my previous design: https://www.thingiverse.com/thing:2637742 The lever arm of this design is twice as long (6" vs 3") making the balance of the scope less...
thingiverse
Altitude bearings for a small Dobsonian telescope. This design includes mounting holes to screw onto the side of a wooden cradle for the optical tube. The bearing diameter is 150mm; width is 25mm. Light sanding of the bearing surfaces might be needed...
cults3d
This is a reflector telescope and stand I designed that uses mostly 3d-printed parts and the rest is very easy to find. Advantages of this design is the hight of the eyepiece, it allows you to stand up straight when looking at the stars so its more...
cgtrader
Dobsonian 16" Telescope 3D model This is a dobsonian model telescope with rich details and realistic shaders. Was fully made on Blender, rendering throught Cycles. ... Colors can be easily modified Original model optimized for Cycles Blender.
grabcad
This is a continuation of my previous project to design and build a 10 inch Dobsonian truss telescope.I managed to acquire a 12-inch (300mm) mirror with a focal length of about f6.This size of mirror makes the overall telescope shorter than the...
grabcad
This is a continuation of my previous project to design and build a 10 inch Dobsonian truss telescope.I managed to acquire a 12-inch (300mm) mirror with a focal length of about f6.This size of mirror makes the overall telescope shorter than the...
thingiverse
Drop-in replacement for eyepiece rack that Orion used to include with all of their XT-series dobsonian telescopes. They still have the pre-drilled holes in the mount for the rack, but no rack in the included accessories. ... This Eyepiece rack fits...
thingiverse
Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...
thingiverse
This printable telescope features a collapsible OTA into a cakebox form that protects the optics, and a dobsonian mount that can be set up and ready for stargazing in less than 5 minutes. The OTA is also compatible with any other Vixen clamp mounts...
thingiverse
Just a support to adjust a laserbeam as finder on my telescope Instructions Print all parts and press them together strongly as on the pictures. Use a rubber band to press the laser against the fine adjustment screws. ...Use two rounded tip bolt.
thingiverse
Just an dobsonian mount. ... Here is all the wood parts: https://www.tinkercad.com/things/9CmM4V9sl0q I use this printed telescope: https://www.thingiverse.com/thing:4294635
prusaprinters
The Micro Scope | A Miniture GOTO Telescope.A fully functional miniture telescope built around the Raspberry Pi HQ Camera, the Raspberry Pi 4, OnStep's GOTO firmware and Canon EOS compatible lenses.For the full story visit my Micro Scope Instrutable...
thingiverse
Customized version of https://www.thingiverse.com/thing:1672381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1672381
thingiverse
Customized version of https://www.thingiverse.com/thing:1672381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1672381
thingiverse
A fully functional miniture telescope built around the Raspberry Pi HQ Camera, the Raspberry Pi 4, OnStep's GOTO firmware and Canon EOS compatible lenses. For the full story visit my Micro Scope Instrutable at |...
thingiverse
This is a shelf to hold up to four telescope eyepieces on a wall or dobsonian telescope mount. ...This is designed for 1.25" eyepieces, but you can easily scale it up for 2" or down for 0.965".
thingiverse
Two eyepiece holders for 1.25" eyepieces for your Dobsonian telescopes. I made two different versions, one for my 6" scope and another for my 8" scope. ...These are very simple to print with no supports.
thingiverse
This is a motorized ('go-to') Dobsonian-style telescope constructed mostly from aluminum extrusion and 3D-printed parts. It also makes use of donor parts from a Celestron C8N - specifically, the primary mirror, primary mirror cell, secondary mirror,...
thingiverse
This is a solar finder designed to fit on the finder scope bracket of my 12" Apertura brand dobsonian telescope. It complements the solar filter mount that I also made here: https://www.thingiverse.com/thing:3555516 I assume Apertura uses the same...
thingiverse
A few upgrade parts for the Sky-Watcher Flex 200P dobsonian telescope: ball bearing hub: A 6 arms hub to upgrade the dobsonian base with ball bearings bottom sleve: A sleve to properly center the M10 screw in the 14mm hole slide sleve: The same...
thingiverse
NOTICE: [The new version now released!](https://www.thingiverse.com/thing:3327081) EQ mount II for small telescope or DSLR, desing for OnStep goto controller. How to make? See my video: https://youtu.be/Dmi01grPYCI FreeCAD sources on...