gpio connectors 3d models
61030 3d models found related to gpio connectors.thingiverse
D) Print your own female-to-female GPIO connector (cheap and nice). Instructions How do I use this? 1) Print this. It takes about 11 mins on my solidoodle 2. 2) Connect your wires to the correct...
thingiverse
... Heatsink Case. ... This looks realy beautifull, but I do not plan to use the GPIO connector. Therefore the connector is always open and I want to protect this for damage and/or short circuit. ... I designed a simple cover for this GPIO connector.
pinshape
SummaryModified blandman's GPIO Connector file to support the 40 Pin connector found on the Raspberry Pi A+, B+, and 2.InstructionsSlides over the GPIO pins so that you can push a bare wire in to make a connection with that pin. ...Printed on a...
thingiverse
Modified blandman's GPIO Connector file to support the 40 Pin connector found on the Raspberry Pi A+, B+, and 2. Instructions Slides over the GPIO pins so that you can push a bare wire in to make a connection with that pin. ... Printed on a...
thingiverse
This is a removable top for the Raspberry Pi 4 Argon One case with a hole for connecting an I2C sensor to the GPIO terminals by a 5 pin female connector
thingiverse
Pretty simple item, sometimes you just want to have the 40 pin connector on your Raspberry Pi to be covered... ...Print Settings Printer Brand: SeeMeCNC ...
thingiverse
When I printed the vexaae's original GPIO connector with a makerbot replicator 2 (PLA filament) the holes would get filled in and some sides failed to print. So I took the blender file he provided and modified it until it worked on my Makerbot...
thingiverse
Based on https://www.thingiverse.com/thing:1874648 but fully rebuilt (because of model artifacts I could not get rid of as easily as rebuilding) This 40-pin GPIO cover is based on the dimensions of the source thing. The remix is: - 4 pins...
prusaprinters
Based on https://www.thingiverse.com/thing:1874648 but fully rebuilt (because of model artifacts I could not get rid of as easily as rebuilding) This 40-pin GPIO cover is based on the dimensions of the source thing. The remix is: 4 pins exposed:...
thingiverse
On that header I put an ribbon cable connector for controlling my bed lighting. This whole setup adds a good 20mm from the case surface to the connector end. Which is to much, since the space between the X-axis motor and the frame is just 8mm. So I...
thingiverse
A cover for the GPIO connectors of a Raspberry Pi. ...Holes are present for 5V and Ground connections so you can connect power.
thingiverse
Customized version of http://www.thingiverse.com/thing:1442094 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1442094 Instructions Using the following options: wall...
thingiverse
Customized version of http://www.thingiverse.com/thing:1442094 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1442094 Instructions Using the following options: hight...
thingiverse
Connect dev boards to pins. Entwicklerboard ohne löten mit Pins verbinden. ...Print Settings Rafts: Yes Supports: No...
thingiverse
Customized version of https://www.thingiverse.com/thing:1442094 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1442094
thingiverse
Customized version of https://www.thingiverse.com/thing:1442094 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1442094
thingiverse
Maybe a stupid idea but here you go - it mounts your rpi via GPIO connector to the frame of your printer. Fits vslot. ...25% infill.
thingiverse
This is just like [the adafruit case](https://www.thingiverse.com/thing:1165227) except it has a 90° GPIO on the side for [this connector](https://thepihut.com/products/40-pin-gpio-connector-header-extender-90-degree-angle) It hasn't been tested yet,...
thingiverse
This is just a simple remix of the simple but good case be rwindr. ... I changed the top part so that the GPIO connectors can be used without having to cut the opening free.