gps mount for motorcycles 3d models
2315409 3d models found related to gps mount for motorcycles.thingiverse
Print using PET or PETG in the orientation shown for temperature and vibration resistance. 50% infill and 4 perimeters is suggested for strength. Two parts are combined into 1 STL file. Hardware used is M4 and M5 stainless fasteners but I've...
thingiverse
Also for me it's just a tad too low so see the GPS at a glance without actually looking down. - `ridepart_35deg_high.stl`, a higher version that can be moved back to clear the tank bag (at which point it will obstruct the main display) at the...
thingiverse
... drive 51, likely will fit other sizes. ... Designed to clamp on a 12mm bar (common gps bar mount for motorcycles). 3-piece design the gps holder a clip on sun shield/top cap, and the back of the clamp. ... setup for use of four M4x25mm bolts and nuts.
thingiverse
My customizable design of a cell phone mount for motorcycles. I used super glue (cyanoacrylate) for joining both parts and a piece of Velcro to attach it to the motorcycle handlebar (with a tiny rubber part under it for preventing the frame to...
prusaprinters
If you don’t know what you are doing, stick to the original parts.Hi,this is a fusion of the original KTM GPS Bracket (64112992033) and the SP-Connect Smartphone mount (61912991044) into one Bracket.You can flip the small bracket to fit your...
thingiverse
This mount is a platform for attaching electronic devices to motorcycle handlebars. This was designed for a Yamaha XJ650, but may work for other bikes. The D123 CAD files are included so modifications can be made. Instructions Others materials...
thingiverse
Stand for gps. The distance between the bottom holes is 21mm. The diameter of the bottom holes is 3mm. Horizontal hole diameter 4mm Стойка для gps. Расстояние между нижними отверстиями 21мм. Диаметр нижних отверстий 3мм. ...Диаметр горизонтального...
thingiverse
I needed a GPS mast to swap onto an existing carbon fiber mast with an 8mm ID. ...This is the perfect size for an M8n puck.
thingiverse
This is a modification for this original thing: http://www.thingiverse.com/thing:768726 My GPS's diameter is bigger than the one in the original thing. I have made the diameter bigger and I have modified the arc a bit in order to make it easier to...
thingiverse
Mount for nz gps. I used a wooden 3mm stick as a macht. ...Also you can check out a foldable version https://www.thingiverse.com/thing:2947440 (a remix from https://www.thingiverse.com/thing:2430107).
thingiverse
A simple GPS holder (Matek GPS) For ImpulseRc Alien frame Have added Version 2 which has a slight raised portion in the center to stop any stress on the connector which can result in disconnect of the GPS. Also the hole is now wide enough to pass the...
thingiverse
This is a remixed version of original GPS mount for the HGLRC M80 GPS.
thingiverse
GPS mount for drone. ...it works with Shark X9 frame but I also attached FreeCAD file to customize to other drone frames.
thingiverse
... a wrap or two of electrical tape if you like) to stick the GPS to the mount. Position so it doesn't interfere with the props. FreeCAD drawing included. Here's my rear mount one for the HD1 and TBS GPS M8.2: https://www.thingiverse.com/thing:5163209
thingiverse
This is a prototype GPS mount for the BQE Bandolero. It mounts using your stack bolts, UNDER the build deck, wedged between the arms. We had mixed results with this part, as some flight controllers were too close to the gps and giving some...
thingiverse
... cup holder. The Universal Phone Tripod Mount attached to it with a 1/4" Screw. I purchased a 2-pack from Amazon for about $8. I've tried several different mounting for the GPS (window, dash, vent, weighted bag, etc.) but I like this one the best.
grabcad
Mounting case for a Pixel 2 designed to accommodate the phone with the Newdery auxillary battery case found here :https://www.amazon.com/gp/product/B07CCG3ZC5/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1The mounting bracket was designed to...
thingiverse
This part was designed for the use of the Micro Ublox M8N GPS module on a mini-quad battery strap. Designed to fit straps about .6" and smaller. A version for both directions of battery mounting. I recommend adding hotglue/rtv around the connector...
thingiverse
Update : remixed the design to make the case deeper, allowing for a bit of foam glued to the bottom cover to act as a preload. This holds everything together more securely. Also increased the size of the charging-port hole. Look for the v9 versions...
thingiverse
Some multicopters just don’t offer a good place to mount the GPS puck. My S-500 is one of those and I’ve seen a dozen different ways that guys lash their GPS pucks to these unfriendly frames. The factory answer is to poke a hole in the light...
thingiverse
... to block the sun. ... designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. Thanks, Enjoy! ...
thingiverse
This is a hard shell strap mount for a 35mm stack mount GPS. The specific unit it fits can be found here... https://www.readytoflyquads.com/mini-ublox-6m-gps-w-35x35mm-mounting-backplane-and-compass I had bought this particular model hoping that it...
thingiverse
This is handelbar mount for garmin mount. ... You can use this mount for prevent rotation simple mount around hendelbars. ... D handelbar 31.8mm Use M3 screw and DIN 16903 plug.