gps mounts for motorcycle 3d models
2315409 3d models found related to gps mounts for motorcycle.thingiverse
Print using PET or PETG in the orientation shown for temperature and vibration resistance. 50% infill and 4 perimeters is suggested for strength. Two parts are combined into 1 STL file. Hardware used is M4 and M5 stainless fasteners but I've...
thingiverse
Also for me it's just a tad too low so see the GPS at a glance without actually looking down. - `ridepart_35deg_high.stl`, a higher version that can be moved back to clear the tank bag (at which point it will obstruct the main display) at the...
cults3d
This support for BMW motorcycle, that I designed for a friend, it receives a Ø16 tube, to fix a GPS
thingiverse
This is a repaired model of the cover for the custom Garmin GPS mount from BMW.
prusaprinters
These are some GPS holders that fits the Nord5 frame:Iflight M8Q-5883 BN220Print in TPU, no supports, with the orientation that is in the file.
thingiverse
... drive 51, likely will fit other sizes. ... Designed to clamp on a 12mm bar (common gps bar mount for motorcycles). 3-piece design the gps holder a clip on sun shield/top cap, and the back of the clamp. ... setup for use of four M4x25mm bolts and nuts.
cults3d
-Garmin GPS bracket for use on motorcycles and bicycles -Can be adjusted to fit handlebars from 1.8mm to 35mm File format STL
thingiverse
The clamp for the mounting bar is here: https://www.thingiverse.com/thing:1322658 This is a work in progress. I ended up reprinting the buttons and the catch and gluing them in place of the originals as the grain of the print is wrong if you print...
thingiverse
This is a SkyRC GPS Speedometer case with mounting solutions for the Arrma Typhon3s specifically as well as a universal GoPro style mounting option. - File#1: SkyRC case with integrated body post mounts for Typhon3s - File#2: SkyRC case with GoPro...
thingiverse
... H main controller under the CG of the helicopter. ...It clips to the frame directly below the main shaft. The other part is for the GPS antenna. This replaces the horizontal fin on the tail boom. ...Use the original screws to mount this to the tail.
thingiverse
Mount I made to attach the pictured style of GPS Speedometer / Compass to the aftermarket "Double Bubble" windscreen of my ZX-14R With a thick enough double sided adhesive foam pad should work for most sportbike windscreens. SolidWorks model include...
thingiverse
I really wanted the bright green so I went with HB PLA Neon Green 1 KG (amazon sells it cheap and it is prime eligible!) The "gaskets" are designed to wrap around the handle bar ends and go underneath the mounts to prevent the mounts from scratching...
thingiverse
You'll need to print the mount and a thumb screw(used to make sure the GPS does not fall out during off-roading) I used rubber grommets under the mount to dampen vibrations and also to raise it up. I used PLA but I think PETG or ABS would be a...
thingiverse
This is a remix of OpenPilot GPS v9 holder (http://www.thingiverse.com/thing:637547) but with added legs to support the holder above your choice of Autopilot (i'm using a revo in the attached images). The dimensions of these legs are designed to...
thingiverse
Very lightweight strap mounts for a BN220 GPS. Designed for max. 20mm wide strap. ... BN220_StrapMount_Top.stl - cable is parallel to a strap BN220_StrapMount_Top_Side.stl - gps rotated 90deg, cable is perpendicular to a strap
thingiverse
- a Lezyne to K-edge adaptor using the Lezyne mount/Fusion 360 file uploaded by CMH - a Lezyne to Go-Pro mount remixed from foo_fighters version - see his thing for details of which GoPro mounts work with it. Both have had the Lezyne mount area...
grabcad
I modeled and created some mounts to use for my motorcycle panniers. I was able to find some scrap steel material for the project. I wanted the panniers to be removable and strong enough to support fully loaded panniers. The concept uses 10 M8 SHCS...
thingiverse
I used double sided tape to pre-mount them for lining up so they can be tweaked prior to drilling the final pieces. The smaller flatter piece was for sealing some pre drilled holes in the bottom of the pannier so I will use some black silicone...
thingiverse
For the oiler, coper and brass fittings you can easily find from the hardware stores. I experimented with ball bearings, but this design seems to have the best flow rate. ... Brass Angle Needle Valve, 1/4" Compression Tube x 1/8" Male Thread 1/2 in...
thingiverse
For the oiler, coper and brass fittings you can easily find from the hardware stores. I experimented with ball bearings, but this design seems to have the best flow rate. ... Brass Angle Needle Valve, 1/4" Compression Tube x 1/8" Male Thread 1/2 in...
thingiverse
This phone holder secures to the standard GPS support bracket in BMW motorcycles that use a cradle for the GPS. R1200GS R1250GS F800GS F850GS. I believe the same cradle is used in R1200/1250RS, older RT models and the S1000 adventure style models. ...
thingiverse
This phone holder secures to the standard GPS support bracket in BMW motorcycles that use a cradle for the GPS. R1200GS R1250GS F800GS F850GS. I believe the same cradle is used in R1200/1250RS, older RT models and the S1000 adventure style models. ...
thingiverse
Garmin mount for my Yamaha FZ6R. ...Untested. Garmin base taken from here: http://www.thingiverse.com/thing:674873 Version 1.1: Thickened up the eye on the GPS mount head. ...Modified the top clip slightly to create better slicing.
thingiverse
This mount is a platform for attaching electronic devices to motorcycle handlebars. This was designed for a Yamaha XJ650, but may work for other bikes. The D123 CAD files are included so modifications can be made. Instructions Others materials...
thingiverse
This is a 2 piece clamp design made to interface with the ACECAR GPS Speedometer, and probably other identical models for sale elsewhere. This fits onto a 7/8" handlebar (Suzuki DL650 in my case) using M4x0.7 nuts and screws. ...Powering the...