grab cad 3d models

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

MAJOR UPDATE [2017-05-05]: New and updated models were added based on suggestions and requests from people who have printed the terrain set (thanks abchiptop). Work log checked off... Checked all decks to be same dimension (5mm thick) - [x] Checked...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

... <p>100%</p> <p><strong>Notes:</strong></p> <p>Print at 100% infill. The tubes are modeled hollow and should print that way Post-Printing Top Finishing Some finishing may be required for the Elite version of the top. Category: R/C Vehicles

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... fills the opening left after you remove the 12 volt adapter socket from the base. It simply slides into place. #Printing# I print rafts with most things, including these models, other than that they are quite simple and shouldn't cause any issues.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

and all they could offer was to return the toolbox completely or bring in the suspect drawers and swap with floor models…This drove me nuts on an otherwise perfect toolbox and I had to fix it...The FixI designed new end-caps to enclose the aluminum...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Many thanks to Dalek_Kolt for providing the original model, you can find more ripped stuff from them here: https://www.vg-resource.com/thread-39778.htmlDisclaimer:The figure you see in the photos is a larger version that houses LEDs and batteries. If...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

For me it wasn't a problem, but I've added a bit of chamfer to the bottom for a bit of extra movement.&nbsp;If you manage to make a square 16x16mm glass then I've included a 16x16 model without the bottom portion that should not limit the camera...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...