gridfinity 2 3d models

This hex bit holder holds:26x short hex bits9x long hex bits2x hex extendersIn a Gridfinity bin 4 tall x 2 wide x 4U tall

There was already another similar project that holds 4 Yubikey 5s, but I have a mix of 5s and 5Cs, and the 5Cs are slightly thicker. Each slot on this cube can fit a 5C or a 5, so you can mix and match as needed. ... FreeCAD source file is included

<p>0.4mm nozzle</p><p>0.2mm layer height</p><p>PLA</p>

A jigsaw blade holder holds up to 15 blades

Customized version of https://www.thingiverse.com/thing:3064519 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3064519

Just wanted a spot for a weatherman wave laying on its side. ... I made another version which is deeper but haven't printed it out to test it yet.

I needed some tool and material blocks for a mobile fly tying caddy but couldn't find anything so I modeled some basic blocks and holders for my most used tools. - Bobbins and Threader 1x1 - Holds up to four bobbins, I'm using Rite Bobbins - Super...

OnShape document available here.

A better way to organize Hanna Test Kits.

I constantly have spare drum keys popping up around the house, and wanted somewhere to stow them.This should fit 4x drum keys with an outer diameter of 10mm, and the pockets are 36mm deep.

Image shows a 6U handle (6u means a 6U bin will fit underneath the handle)

This design holds an Apple MacBook Charger 96w. ...Occupies 1x2.

Customized version of https://www.thingiverse.com/thing:5428104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5428104

Customized version of https://www.thingiverse.com/thing:5428104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5428104

A thing to hold the SATA 32-piece feeler gauge set (ST09407SJ).Here's a link to the tool:https://www.satatools.us/products/automotive-specialty/feeler-gauge-sets/st09407sj-32-pc-feeler-gauge-set-002-100mm

Another 1x2x4 unit that could store vertically two D batteries.Without magnet holesWithout stackable lips (as it is not stackable)Battery holes are 34mm wide.I printed mine with :PLA+ (Creality PLA Hyper)Low quality (0,28mm layer)150mm/s10% infill2...

Customized version of https://www.thingiverse.com/thing:5428104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5428104

Took the ingenious design of the original and made the frame less bulky so it could sit at the back of a table. To save on filament, I would recommend changing the screw length of the original to fit your needs.Also added honeycomb for structure and...

Customized version of https://www.thingiverse.com/thing:5428104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5428104

The pegs from the screwdriver holder (by Akinayr) were spliced on the bin from HuMa's collection of ultralight bins. ... The pegs were also modified to adapt to the contour of the bins' base.

Customized version of https://www.thingiverse.com/thing:5428104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5428104

Holder for the Husky SAE set of 7 nut drivers from Home Depot. ... Prints in two halves.