groove mount 3d models

The normal groove mount plates were too large for my delta style 3D printer carriage, so I designed something that fits the space as well as clamping the groove securely to the mounting plate. For more info, check out:...

This mount allows mounting of a BLTouch sensor on a Groove Mount for an E3D style hotend. Offset is 25mm in the Y axis. Two versions - one for the V6 (not tested!), and one for the Volcano. ...

The groove mount that I received with my J-Head from MakerFarm was too large to fit underneath the effector and had through holes in the wrong locations. I quickly drew up this modified groove mount in OpenSCAD. Update 7/14/2013: I've uploaded an...

Bowden groove mount adapter for the intake hole, that is wide enough to fit a 4mm pfte tube. Please be aware the inner hole might shrink, so adjust your printing parameters to compensate. ...The tube should fit snug and not really move much.

... plate. Simply remove the original Hot End and supporting hardware. Slide on the mount and align the Groove Mount adapter of you hot end into the recess that teflon barrel of the original hot end used to align with the Filament Drive. ...

This is a groove mount adapter that fits into the Titan extruder to mount it to a CR10 V2 or V3 The threaded bit is an M10x1 that is 8mm long It screws right into the top of the hot end to mount a titan extruder Print with at least 0.15mm layer...

Hot end and Nimble need to be aligned properly, this groove mount adapter does that. ### The Nimble Extruder With an installed weight of less than 27 grams on your carriage/effector the Zesty Nimble is smallest and lightest extruder you can buy, it...

Rather than placing FSRs under the bed as originally proposed (http://reprap.org/wiki/FSR), I decided to put FSRs on the groove mount. Two FSRs are placed between the two parts of the groove mount. This method allows to probe with lower pressure on...

I couldn't find a groove mount plate that supported the barrel groove all the way around the groove, top and bottom so I designed one that does much better at that. If the plate thickness is tailored to the groove correctly, it securely holds the...

:) My plan is to get this working well and then modify other extruders like the Printstruder and Wade Extruder to accept groove mounts. I think this would be better than epoxying or drilling holes into the sides of the insulator and is definitely...

Try it!

This is a printable version of the groove mount adaptor delivered with the Merlin Hotend set. The walls ar epartially very thin, so make sure to have strong layerbondig. ...It does work with ABS, but PC would be better.

This is a groove mount plate for E3D V6, V6, J-Head and similar hot ends. I am using it on a Prusa Mendel i2 X carriage. I've had good results annealing this part. ...

This is my attempt at mounting a Trianglelab Dragon hotend on a mk3s+ in a way that supports one handed nozzle changes.In order to stop the hotend from rotating during nozzle changes the included round aluminum groove mount adapter is replaced by new...

Therefore, I adjusted the design to feature a groove mount, allowing you to remove the temperature sensor from the base. This makes it possible again to remove your 3D printer from the enclosure. Support If you want to support me for the designs I...

Therefore, I adjusted the design to feature a groove mount, allowing you to remove the temperature sensor from the base. This makes it possible again to remove your 3D printer from the enclosure. Support If you want to support me for the...

Groove mount for Geeetech Prusa I3 acrylic (8mm) with proximity sensor mount. ...Just print two of the clamps if you don't need the sensor (you may want to print an extra one to use as a spacer if your hotend ends up too close to the X plate).

I was using a groove mount for my E3D V6 hot end, but it was a little bit loose in the groove and would slide back and forth. I modified this so that the hot end would not be able to slide anymore. The two pieces press fit into each other. ...It is...

Therefore, I adjusted the design to feature a groove mount, allowing you to remove the temperature sensor from the base. This makes it possible again to remove your 3D printer from the enclosure. <b>Support</b> If you want to support me for the...

This is just an extruder mount to make the mk8 compatible with j-head groove mount also compatible with the link to the original design. The original design were off to the right by the designer because he wanted to have the motor rest on the hot...

It mounts standard [PC4 M10 4mm pneumatic fitting](https://www.amazon.com/YOTINO-Straight-Pneumatic-Connector-Long-Distance/dp/B078SRBDS7/ref=sr_1_3). The PC4 fitting has better grip on the Teflon tube and prevents the extruders from pushing out of...

From Tony Busers original thing: This is a grooved insulator retainer/mount for a MakerBot plastruder. This is for MakerGear makergear.com/products/nozzle style grooved insulators. (Pictured here is one I got from Brian Reifsnyder...

The mount hole spacing is now configurable in OpenSCAD so you can easily make one for the Printruder II if you want. Also, I've made a few other tweaks to make it easier to fit the insulator, but might still need some cleanup to widen the slot so...

The mount hole spacing is now configurable in OpenSCAD so you can easily make one for the Printruder II if you want. Also, I've made a few other tweaks to make it easier to fit the insulator, but might still need some cleanup to widen the slot so...

I didn't really like the shape of this: http://www.thingiverse.com/thing:641300 mount so I modified the shape, the fit is still the same. ... UPDATE V3; made the 50mm holes countersunk because my E3D fan didn't fit under the bolt, also made the whole...

This is a slightly modified version of thing:3287069 optimized for CNC machinig. ... It is a groove mount for the JGAurora A5 to replace the stock extruder with an e3d v6 or any other groove mount hotend

This is a slightly modified version of thing:3287069 optimized for CNC machinig. ... It is a groove mount for the JGAurora A5 to replace the stock extruder with an e3d v6 or any other groove mount hotend

adapts the V6 groove mounting system to fit the screw mounting system of newer slice engineering hotends. prints without supports if you lay them on their flat faces. ...youll need some m3 nuts and bolts

adapts the V6 groove mounting system to fit the screw mounting system of newer slice engineering hotends. prints without supports if you lay them on their flat faces. ...youll need some m3 nuts and bolts

A small adapter to support groove mount hotends to the V5 mount of the Anycubic Vyper. ... You need 2 M3 screws and 4 brass inserts.