gt air 2 cardo 3d models
1001447 3d models found related to gt air 2 cardo.thingiverse
My first try Shoei gt-air2 GoPro chin mount. Suits good M and S shell sizes. Try first at low infill to check that it suits well for your helmet. ... 21.03.2021 - Added vertical mount (for any reason you want mount it 90 deg)
thingiverse
Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444
thingiverse
Earpad ring for a shoei gt air model (not for gt air II). The ring holds a scrub sponge to avoid the noise of the air at high speed. The ring of the picture was an older version, it still did not fit perfectly. ...The stl file fits ok.
prusaprinters
Cardo Packtalk Edge mount for Shoei helmets compatible with SRL-2Recommended settings: 4+ walls, infill - yes ;) , layer 0.2mm, brim 5mm+, supports: Yes, only on the table + forced support in place shown in one of pictures.Recommended material: PC,...
grabcad
This is a 3D printed stand that will hold a pair of Cardo Packtalks or Packtalk Bolds with the USB connector facing up for easy charging.
cults3d
The ideia was to create an adaptor that was integrated using the Nexx X-COM helmet port and the system used in cardo (like the glue plate) to fix the Cardo Freecom. ... I've added a new and improved version of the first design.
thingiverse
my stand for Huawei GT 2 Smartwatch. Designed to hold the charging plate pretty firm. ... easy to print and use!
cults3d
Clip created to close 6 mm wide Gt 2 belts. I designed it because my Artillery came with the straps tied by flanges and eventually they escaped and gave no option to tension / relocate without changing the flange. It also serves to tighten the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: additional_tooth_depth = 0 m3_nut_hex = 1 pulley_b_dia = 20 no_of_nuts = 1 pulley_b_ht = 8 additional_tooth_width = 0.2 retainer_ht = 1.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options: base_height = 6 screw_profile = 4 idler_height = 1.5 belt_retainer = 1 belt_idler = 0 motor_shaft_diameter = 5 toothed_part_length = 4...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options: nut_shaft_distance = 1.2 motor_shaft_diameter = 5.5 screws_disposition = 3 nut_shape = 1 base_diameter = 19 belt_idler = 1 base_height = 9...
cgtrader
Beechcraft King Air B200 GT loft model ...I skipped some details, ailerons, flaps, rudder ... still working on it ... ... will try to do as much details as I can (landing gear, fuselage frame, ribs on the wings and tail stabilizers)
cgtrader
Beechcraft King Air B200 GT loft model ...I skipped some details, ailerons, flaps, rudder ... still working on it ... ... will try to do as much details as I can (landing gear, fuselage frame, ribs on the wings and tail stabilizers)
thingiverse
This mounting bracket uses 3 wire ties to securely fasten the female 2.5mm headphone jack to the edge of the Cardo mounting bracket. Because Cardo mounting brackets are universal, it should work with most models... ... This item was created in...
thingiverse
GoPro Helmet chin mount for a Shoei GT Air. Worked well and fits the chin profile good. Used GoPro double sided tape to attach. Tested on a few rides and has held up fine. I used PLA to test the mount, but choose your material carefully. ...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options: retainer_height = 1.5 belt_retainer = 1 toothed_part_length = 4 base_diameter = 20 screws_disposition = 2 screw_profile = 4 profile = 12...
prusaprinters
This shim was broken on my Cardo Packtalk slim. You can buy it only in a mounting kit. ...So, I created a replacement</p>
thingiverse
SPANISH VERSION AT: http://reprap.org/wiki/Prusa_Aire#PRUSA_AIR_2.2C_Redise.C3.B1o Instructions To close the entire set will use a squads that I bought at the hardware store, I don't know as universal they are, so I put the plane and in any case can...
thingiverse
### Huawei Watch GT 2 Stand ### I couldnt find a Stand which hides the cable so i designed one myself. Make sure to rotate the Top-part flat on the ground. You will just need a tiny support for the Bottom of the Bottom-part cable-channel. I...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: nut_shaft_distance = 1.2 additional_tooth_width = 0.2 m3_nut_depth = 2.7 pulley_b_ht = 8 m3_nut_hex = 1 retainer_ht = 3 no_of_nuts = 1 idler_ht =...
thingiverse
... not many charging stands for this beautifull watch so I designed this one in Fusion, looks sleek, fits perfectly and prints relatively quick. ...5hrs 30mins at .2 layer height and 35mm/s. Print orientation is to be seen on the second picture. ...Enjoy
cgtrader
High detailed, correctly scaled model of 1965 Broadspeed GT 2+2 coupe. Originally created with 3ds Max 8. Rendered with V-Ray, files with standard materials are included. Unit system is set to metric units. Model is built to real-world scale. ...
cgtrader
High detailed, correctly scaled model of 1965 Broadspeed GT 2+2 coupe. Originally created with 3ds Max 8. Rendered with V-Ray, files with standard materials are included. Unit system is set to metric units. Model is built to real-world scale.
thingiverse
I needed a mount for my Runcam Air Unit to mount in the Zohd Talon GT Rebel. Mound hardware and slip into nose of plane, then connect wires. simple. Very basic, and probably not best design, but it does the job. ... Mod if you like.
thingiverse
Back Window with Air Intake for Jomurema GT-01 Mini-Z Body. You can Use a Middle Dampher System under this Back Window. Thats the Idea behind it. If it to little, please Contact me. ... Watch at my other Designs for other Things for the great...