gu10 lamp fitting 3d models
441404 3d models found related to gu10 lamp fitting.thingiverse
This is a simple GU10 I use for my desk and workbench. ... The vitamins are a ceramic GU10 holder and a M5 wingnut and bolt. ... Update: I've added a magnetic base, which uses a 10mm x 2mm neodymium magnet.
thingiverse
... smart, however, the original bulb holder was for e27 fitting and all the smart e27 bulbs I could find were too tall. ...The GU10 versions were much shorter, so I designed this part to take a standard GU10 socket and replace the holder inside the lamp.
thingiverse
simple 3D model made from measuring a Osram LED Star lamp with GU10 socket pins and light diffusor cap. Used with my LED glas lamp stand. ... https://www.thingiverse.com/thing:3936221
thingiverse
If you have any questions feel free to ask:) below you have samples of non printed parts: bulb holder:...
thingiverse
Fits for IKEA, Philips, innr, Osram and other GU10 LED Spots. You can combine both bodys with both inserts. ... Height: Large Body 97 mm; Small Body 82 mm For LED Spots only!
thingiverse
### This is a simple GU10 lamp socket which I used for lighting my attic. ... ## Changes made * The base part was a little to loose for my taste, so I made it tighter to not accidently let the socket fall off * Re-Aligned the socket * Made a...
thingiverse
This is derived from articulated PCB arm by giufini:http://www.thingiverse.com/thing:801279 I've used 5 joints between the wood base and each lamp shade due to a GU10 socket cable length limitation - 13cm / 5". It is sufficient to position the lamp...
pinshape
SummaryThis is derived from articulated PCB arm by giufini: http://www.thingiverse.com/thing:801279 I've used 5 joints between the wood base and each lamp shade due to a GU10 socket cable length limitation - 13cm / 5". It is sufficient to position...
thingiverse
---------------------------------------------------------------------------------------------------------- A lamp that I designed for our kitchen. The aim of this project was precisely the combination of LED strips for indirect lighting and GU10...
prusaprinters
Gerade die Kombination von LED-Strip für indirekte Beleuchtung und GU10-Strahlern für eine gerichtete Wirkung war Ziel dieses Projekts. Um die Teile auf die Druckplatform zu verkleinern, habe ich sie in Stücke aufgeteilt. Der Diffusor wird 4 mal...
youmagine
I bought these nice Philips Led lamps couple of years ago and they were supposed to fit into my ceiling where I measured free height of around 8cm which was enough for them to fit. Unfortunately, not every hole did have the same free height so...
cults3d
... My LED Lights are very small. If you are using bigger ones they may stick out. Size: 150mm x 76mm x 73mm Screws: 4 x M3 16mm screw and nut for the Gu10 sockets 2 x 3.9mm x 30mm srew and dowel for the wall mount 4 x 2.9mm x 10mm screw for the cover
thingiverse
... LED Lights are very small. ...If you are using bigger ones they may stick out. Size: 150mm x 76mm x 73mm Screws: 4 x M3 16mm screw and nut for the Gu10 sockets 2 x 3.9mm x 30mm srew and dowel for the wall mount 4 x 2.9mm x 10mm screw for the cover
thingiverse
Notes to the design: The taps can, when printed at some printers (at least mine), break off, but the shade fits quite firmly to the holder, and this will normally be enough to hold it, otherwise glue will do the trick. Preparing the print:...
thingiverse
HY This is for GU10 Lamp lamp_kopf print with rafts and supports, lamp_oben/_unten only supports lamp_teller no rafts no suports nut and screw m6x30 THX
thingiverse
Simple LED lamp for hanging or standing Led GU10 bulbs required (LED spots GU10) GU10 fitting 230V The lamp can be adjusted to three different angles. In some 3D printers want to set the scale 102% or 105%. A lot depends on the manufacturer of LED...
cults3d
make a lamp with a can or a jar with a GU10 LED bulb! the nut fits perfectly to the holder, does not need post-processing! 2 versions for flat (6x4mm) and round (5mm) bipolar cables! be careful with the sharp edges of the can! ... (necessary...
thingiverse
**UPDATE 14/07/17** Added ventilated versions of both cans to aid with heat dissipation The print requires a couple of standard additional parts available from pretty much any hardware store: 1x GU10 ceramic base 4x 10mm M3 bolts and nuts 2x 3mm...
thingiverse
After of about 9hours of print you will need: 4x M3x35mm screws with nut 2x M4x10-15mm screws with nut 1x GU10 socket 1x GU10 Led lamp Is ready and tested, working well but i would like more opinions or suggestions. ... Only update will be about more...
thingiverse
Inspired by three things on Thingiverse: Articulated PCB Workstation by giufini http://www.thingiverse.com/thing:801279 Pointy Star by iamnotachoice http://www.thingiverse.com/thing:563306 And my own "ordinary" version of GU10 lamp...
thingiverse
Simple cylinder on Tinkercad slides over exposed LED GU10. Has nice translucent color (PLA) and shows white light ring at bottom. I drilled two holes and used thin wire across bulb or hot glue works. ...May be a better way to mount.
thingiverse
Lampka ma dość spore luzy dla łatwiejszego pasowania dekla i litho a także samej żarówki gu10 LED!!! niemniej jednak jak wspomniałem wcześniej może zajść potrzeba przeszlifowania gwintu pierścienia i górnego dekla dla łatwiejszego skręcania. :) ). ... ...
thingiverse
And the height/length of the fitting (to the lamp). You can change the inner diameter as well, however be careful that the thread does not change! The 2nd photo shows one lamp with and one without the nut. It is intentially over the lamp fitting as...
thingiverse
... everywhere. You can use hot glue to keep it in place. However the mold is very acurate and it also has a tight fit. The height of the mold is done for the measures of a Shelly DUO GU10 lamp with 73mm*50mm. ...Other GU10 Spots MAY or MAY NOT fit.
thingiverse
With this part, you can mount a GU10 lamp on an IKEA Tertial lamp and use the two additional GoPro mounts for everything else :) Parts: - IKEA Tertial lamp: https://www.ikea.com/gb/en/p/tertial-work-lamp-dark-grey-40450802/ - Any GU10 bulb:...
thingiverse
Angled LED Lamp for GU10 Sockets. The Lamp should be mounted at the front left oder front right corner (i glued the Lamp on a Corner Cover you can find here on Thingiverse). I wanted a light on my Ender 5 Printers, but all the existing Lights i...