guide pulley 3d models

... now. I made this using a working guide pulley, keeping all the dimensions as accurate as possible. Since FDM printers are sloppy, extra clearance might be needed on the inner surface. ...The STEP file is included to easily make this change.

a simple filament guide pulley. this design has a opening that allows filament to loop over it. the pulley is 45deg bent. requires a 624ZZ 4x13x7mm ball bearing. ...the 2 parts snap together quite snugly but a drop of acetone at each of the 3 joining...

This is a simple guide pulley for ropes up to a diameter of 10mm. The roll has a diameter of 60mm. Print the roll twice and glue it together. ...Print Settings Rafts: Doesn't Matter ...

Simple filament pulley guide to suit Anet A8 and prevent drag from pulling filament over the Anet frame. ... Require 1x 608 bearing for the hub.

Sturdy filament guide that swivels with a pulley for smoother action Let you imagination flow! ... Instructions I used a piece of filament to create pins for the axle and swivel but a nail or bolt would...

a little guide pully for 4 - 6mm rope. ...

- Infill 5% - arm 10% - base pulley 10% - base support 5% - pin 10% - pulley Designed and inspired by: https://www.thingiverse.com/thing:5193117 Go and check it out :D Just printed the extruder due to "pulley-mecanic-like" theme on my printer and the...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: retainer = 3 teeth = 8 profile = 6 retainer_ht = 8 m3_nut_flats = additional_tooth_depth = nut_angle = 90 idler = 3 m3_dia = 3.2 motor_shaft = 5.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=52373 Instructions Using the following options: Bearing_Outer_Diameter = 9 Flange_Depth = 1.25 Bearing_Width = 4 Pulley_Thickness = 3 Rim_Count = 3 Belt_Width = 1.75 Flange_Thickness = 2...

I use this to guide the filament on my cr3. I zip tied it to a tool tray that sticks out from the top rail. ...Works well, use a drop of oil on the axle.

This gave me the flexibility to slide the control box out of the way when not using the printer and allows me to position it to anywhere convenient when I am printing.I've run it successfully like this for a while now but the filament was causing...

I thought about pulleys with ball bearings but spotted the idea to use the modified gear bearing as a pulley. The elegance of this caught my imagination so I designed a bracket to slide over the X stepper, which is a very good fit but I've included...

guide pulley for bearings 608 (22mm) and 625 (16mm)

11T, 12T, 13T & 15T guide & pulley wheels for rear derailleur. These wheels need 688ZZ bearing(1685mm) for mounting. ...Each wheel set needs 2 bushings.

I updated my Ender 3 to a Direct Drive Mod and installed this update: I ended up printing and installing this side arm spool holder: https://www.thingiverse.com/thing:4888950 I wanted to make sure the filament was sooth to the extruder so I built...

This is a handy way to guide or change the direction of 1.75mm filament. No bearing necessary. After printing, use a piece of filament for an axle. The filament feed can go either under or over the wheel as necessary.Can be mounted with either a...

SummaryThis is a handy way to guide or change the direction of 1.75mm filament. No bearing necessary. After printing, use a piece of filament for an axle. The filament feed can go either under or over the wheel as necessary.Can be mounted with either...

Filament Guide With Pulley from Filament Spool to Extruder 1 608 Bearing 2 Half Pulley 1 Bracket 2 Bearing Covers 1 Bearing screw 1 Nut 1 Whasher Printed with Dagoma DiscoEasy200

1. Chamfered the edge of the hole to ease insertion of the bearing. 2. Slightly increased the hole diameter to ease insertion of the bearing. 3. ...Changed to a 12 sided polygon, just because I like to watch it go 'round (still works with the original...

only workout

3d Files for the Camera Slider video posted by DIY PERKS (https://www.youtube.com/watch?v=GE37xI14Fyw). ... 22 mm by 7 mm baring in the midel

I 3D modeled this exact pully.http://www.banggood.com/8mm-U-Groove-Ball-Bearing-0840UU-Groove-Guide-Pulley-Sealed-Rail-Ball-Bearing-84020_7mm-p-1046816.html Exact one used in DiyPerk's how to make a diy camera slider All you need is ball bearings...

This filament guide pulley allows me to put a CAT-6 box loaded with ABS filament on the floor, run the filament up and over the pulley, and down into the extruder. It is low friction, large diameter and has a deep slot to help guide the filament. ...

The filament was actually wearing a groove into the side of my 3D printer, so I looked for a guide to prevent that. I found one, and tried it, but the filament cut a groove in that too. So, I remixed it to have a pulley that will turn and reduce the...

suspension-arm/gear-pump/safety-valve/guide-pulley/geared-pulley

... of the sensor. So I relocated the sensor to the top of the pulley guide to make feeding easier. There is also a slot to hold the sensor wring and an addition wire support. ... The pulley uses a standard 608 bearing and all screws are M3

I have redesigned the same model with some modifications to fit my smaller bearing and also with a ENDER embossed Text instead of some grooves. ...Inspired by this user.

I have redesigned the same model with some modifications to fit my smaller bearing and also with a ENDER embossed Text instead of some grooves. ...Inspired by this user.

GUIDING IDLER PULLEY