guitar knob 3d models
42542 3d models found related to guitar knob.
grabcad
Have you lost one of the knobs for your Fishman guitar preamp? I did, and so I made this replacement replica. I couldn't find any replacement knobs online, so I remodeled this one from scratch. ...It fits perfect.This knob fits the Aura® Spectrum DI...
thingiverse
The knob can be installed with a set screw or just friction fitted. I used mine on an Ibanez SR300 electric bass guitar. ...Print Settings Printer Brand: Ultimaker ...
thingiverse
I wanted a Basic Knob for my guitar, The one I found on Thingiverse were too tall and I wanted something very discreet. So here it is! it fits well on potentiometer like the one on the picture (6mm diameter approximately) I put the solidwork...
prusaprinters
Print, paint and enjoy this Demon Skull Guitar Knobs, Metallica style inspired
thingiverse
A simple guitar knob. ... Made from this Rose Cabinet Pull: https://www.printables.com/model/31902-rose-cabinet-pull
thingiverse
Remixed into a guitar knob that fits a Dean VMNT. ...Recommend to print with raft and supports, but its really hard not to break off the jaw parts.
grabcad
It's a guitar knob... shaped like a gear. Made for a Strat. (Can't remember the hole size.... ...but it's an easy subtract to get it to fit, right?)
thingiverse
I edited the skull modell to be a guitar knob for 6mm shaft potentiometers. You should print it with supports touching the buildplate, angle 60degrees. I printed it in 0.12 "magic" layer hight and it came out pretty good. ...It may need some drilling.
thingiverse
Should fit about any standard guitar knob splines. Might be a little tight. I used a 0.2 mm hole offset setting in the slicer (Cura) and it fits well. I printed it face up so that all the supports are in the back and in the hole and not on the...
thingiverse
This is a easy printable tool to safely remove guitar knobs by allowing you to equally apply upward pressure to remove it. Also, using plastic will not scratch or harm your guitar compared to prying it off with a screwdriver or pliers. eSun PLA: ...
prusaprinters
Also, using plastic will not scratch or harm your guitar compared to prying it off with a screwdriver or pliers. eSun PLA: https://amzn.to/2MXW95n Video of use: https://youtu.be/Mby0d14o2Xs Enjoy. Print instructionsCategory: Music Summary This is a...
thingiverse
... a video here: https://www.youtube.com/watch?v=iJs2pvlNpP0&t=151s To see the bands performance skip to minute 49 of the video. Other guitar knobs I've designed: https://www.thingiverse.com/thing:2598983 https://www.thingiverse.com/thing:2596494
grabcad
how about some nice, semi-complex guitar knobs! I started making this for a friend a while back while I had access to the school's 3d printer, but alas, as I'm now heading to a much bigger university (and am dying to get my hands on their mech shop)...
thingiverse
... Addendum: The second stl file here "cover" is a chunkier version and instead of pilot holes on the back, I modeled in a big enough cavity so that it will fit snugly over an existing, smaller guitar knob so that the final piece has proper threading.
thingiverse
A custom control knob for a guitar or any other instrument. This knob goes to 11 which is louder than 10. ...This is what inspired me to make it go to 11https://www.youtube.com/watch?v=KOO5S4vxi0o
thingiverse
This is a Death Star Volume knob for electric guitars .. It is a press fit for the standard size 6mm shaft. I use the radar indent for the position marker.. who needs to turn it up to 11 when you can decimate Alderan,LOL print orientation is as shown...