hagrid 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

While some complained about the expenses both in development of such tecnologies,a nd its application on the mech, the Fronc goverment applacate such concerns with the generous loan from the Alliance members.Gone is the troubling Andora-made gyro,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Tree Supports and possibly Outer Brim required for some STLs NOTE: The STL Models may display some artifacts from revision builds, but will not appear in Print RECOMMEND: Allow pieces to cool to room temperature on printers Heatbed before removing to...

Any sagging of overhangs that occur at the very top/front of the model can simply be trimmed or cleaned away after. The mount can be either just press fit (if tight enough) or glued in place into the holes on the back of the body. I recommend gluing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

A hard case for your Eggtracker Mini to use with high power model rockets. Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_extra_port_y_position = 30 custom_back_camera_x_position =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.25 stencil_pattern_line_thickness =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

MAJOR UPDATE [2017-05-05]: New and updated models were added based on suggestions and requests from people who have printed the terrain set (thanks abchiptop). Work log checked off... Checked all decks to be same dimension (5mm thick) - [x] Checked...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

### Bridge style cards (58mm x 88mm) * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Open.stl` * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Covered.stl` *...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

 The SFX version backplate does not fit the build plate of a Prusa Mk3, so this project is temporarily on the pre-prototyping stage.For the FlexATX version, click this link. The enclosed design includes two types of motherboard trays of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

Entry point for USB wire, hole has a separate part for covering it: + usb_wire_cover - base_bracket2_corner_RH x1 - base_bracket2_corner_RH_back x1 - base_cover_big x2 - base_cover_small x3 - base_cover_corner x2 * Front covers: base model is...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

Then, I saw it mentioned by a popular modeller on his YouTube channel, and over the next year, the number of downloads went up enormously. So, it seems like it's time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

The one thing most existing models seem to be missing is the funky characters on the keys. I looked around and found a font that looks just like what they used (basically an old computer font like the one used at the bottom of checks, ...) As I...