ham it up sdr 3d models

7mm and 4mm coil jigs for OSIEM.NET.PL SDR UP Converter v3

7mm and 4mm coil jigs for OSIEM.NET.PL SDR UP Converter v3

... is a precise 4 millimeters. Pump it Up arrow: Pump it Up arrow measures around 10cm x 9.7cm x 1cm (Length x Width x Height), under normal circumstances, not scaled up or down. ...Pump it Up arrow hole size is consistently 4 millimeters in diameter.

It is an ashtray that has "I LIKE IT UP THE ASH" in the base. ...It will melt after dozens of uses but it is a plastic ashtray so what do you expect.

Couldn't find any pop-up print designs online so I designed one myself in fusion 360.Make sure to tip the exterior onto one of its open edges in your slicer to simplify the need for support. ... I used tree supports which worked fine.Time and flilament...

We unintentionally purchased pop-up style post-it notes, prompting us to seek a dispenser solution. To create the holder, we printed it using the orientation specified in the STL file, with supports added only for the slot that would hold the...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using the following options: xTranslate = 50 degrees zRotation = -45 degrees clockwise zScale = 35 times larger wholeMessage = "Revolution/It's Up"

http://www.thingiverse.com/apps/customizer/run?thing_id=50885 Instructions Using the following options: hole_radius is set to 2.5 mm message_one is displayed as Rev It Up! ...message_two proudly reads Liberty Middle School sign_size has been set to zero...

Pioneering Toolmaker creates Hand Gripper for Ultimate Challenge - Handles Up To 3 Heavy Rings At Once

These are the printed parts needed to build my DIY Pump it Up dance pad. It's constructed out of wood, 3D printed parts, and acrylic. To get more information on this project, please visit www.blowingstuff.com/projects/2020/06/06/piu-dance-pad.html.

This case is designed for the original motherboard of the Muglahite SDR receiver, for those who would like to have it in plastic, or you do not have enough money for the original author's case (The original case wins in strength and isolation from...

These are the printed parts required for my DIY Pump it Up dance pad. It's built out of wood, 3D printed parts and acrylic, and further details can be found here: http://www.blowingstuff.com/projects/2020/06/06/piu-dance-pad.html To make a complete...

https://www.youtube.com/watch?v=j-emlb2_jdI Full write up coming soon https://www.adafruit.com/product/3489 https://www.adafruit.com/product/1317 https://www.adafruit.com/product/3501 https://www.adafruit.com/product/1304...

This is a dispenser for the Post-it Popup notes that fanfold out. ... As always, if you make it, I'd love to see pictures!

 Full write up coming...

Print Settings Printer: Creality CR-10S Rafts: Not Required Supports: None Needed Resolution: .2 Infill: 10% Notes: Printed with PETG How It Was Made This design was conceived in Fusion 360, a swift process that took only about 15 minutes to...

This is a creator of the Post-it Popup notes that unfold in a fan shape. ... As always, I would be thrilled to view images if you decide to bring this into existence!

This is a makeshift post-it holder that accommodates standard-sized notes measuring 76mm by 76mm. To create this solution, you will require two standard rubber bands. ...Begin by cutting these rubber bands to size, then proceed to thread them through...

We hope you enjoy Edit: sorry tribe, the plain tape measure wasn't enough for us so we also dated it. ... Here is our Sunlu Affiliate link https://www.sunlu.com/?sca_ref=507104.Qc1O4Eu3lJ Visit us on Patreon.com/thefreeheathenworkshop check out...

We hope you enjoy Edit: sorry tribe, the plain tape measure wasn't enough for us so we also dated it. Here is our Sunlu Affiliate link https://www.sunlu.com/?sca\_ref=507104.Qc1O4Eu3lJ Visit us on Patreon.com/thefreeheathenworkshop check out our book...

... and bashed this thing together with Meshmixer. Its meant to be an interesting unga-bunga-caveman-style printer test (ie. hit the magic button, hope for the best), but its not nearly as hard as it could be. ...Might be ok, might not be ok, I dunno.

sdr casing for blade rf

This is an approximation of the Kraken SDR generated from specifications found online.

Customized Version of Thing 356988 Crafted with Precision by Customizer! View Original Design at www.thingiverse.com/thing:356988 Explore Unlimited Possibilities with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=356988

This STL was created in support of the individuals participating in Autism Awareness Day, and can be customized to serve as a night light cover. ...To learn more about this cause, visit http://www.lightitupblue.org.

Need hand these out sometimes

faces_segment = 20textstring1 = FAFOtextstring2 = Fuck Around & Find Outtextsize1 = 32textsize2 = 14distance = 1.1fontname = Alfa Slab Onebase_radius_add = 4baseheight = 2cutangle = 60text_excenter_factor = .8direction = upRoundBase = 1

Construct a versatile container that can be stacked to your desired height.

For those interested in Software Defined Radios, I designed this SDR mounting Bracket using Solid Edge CE. The mounting flange on the Antenna side is split to allow the use of an SMA to BNC adapter. ...Works well to attach your RTL-SDR dongle to a...

... for a DVB-T flash adapter such as the RealTek RTL2838 DVB-T USB Stick found here: https://commons.wikimedia.org/wiki/File:RealTek_RTL2838_DVB-T_USB_Stick.jpg. ...If you plan on using it with higher frequencies like 1500MHz, be sure to keep it cool!