hand crank gear 3d models
176874 3d models found related to hand crank gear.thingiverse
this is my first project and it may have a few kinks but it works you can fix things here https://www.tinkercad.com/things/1Gat0q8kya3
thingiverse
... or worry about the crank handle slipping off so the gear post is now combined with the collet and the handle is held on by a threaded cap. The Hand Crank Gear Collect assembly replaces original parts: Winder_Crank_Axle and Winder_Crank_Pin
grabcad
6 inch pitch diameter gear with 36 teeths and 3 inch pitch diameter with 18 teeths.
myminifactory
When i printed the Hand Cranked Heart gear (http://www.thingiverse.com/thing:253934 and http://www.thingiverse.com/thing:243278) the large gear kept skipping because of too much space above it. I printed this ring and now everything is running...
cults3d
When i printed the Hand Cranked Heart gear (http://www.thingiverse.com/thing:253934 and http://www.thingiverse.com/thing:243278) the large gear kept skipping because of too much space above it. I printed this ring and now everything is running...
thingiverse
When i printed the Hand Cranked Heart gear (http://www.thingiverse.com/thing:253934 and http://www.thingiverse.com/thing:243278) the large gear kept skipping because of too much space above it. I printed this ring and now everything is running...
cults3d
Inspired by the paper hand cranked geared heart video, and emmett's brilliant geared heart design, yet having too little time to create one entirely on my own, I incorporated emmett's geared heart into this design to create my hand cranked PLA...
myminifactory
Inspired by the paper hand cranked geared heart video, and emmett's brilliant geared heart design, yet having too little time to create one entirely on my own, I incorporated emmett's geared heart into this design to create my hand cranked PLA...
myminifactory
Emmett's geared cube, with a hand crank. Video of pre-lubricated just off the printer version is here: https://www.youtube.com/watch?v=jfh5DNGP8tw. Printed in PLA on a Makerbot Replicator 2 using Makerware 2.3.3.42 "Standard" settings. A video...
cults3d
Emmett's geared cube, with a hand crank. Video of pre-lubricated just off the printer version is here: https://www.youtube.com/watch?v=jfh5DNGP8tw. Printed in PLA on a Makerbot Replicator 2 using Makerware 2.3.3.42 "Standard" settings. A video of...
myminifactory
The Beth's Hand Cranked Edition would have been fine for me, but I needed it to take some abuse and be conducive to 6-year old dexterity without skipping gear teeth (which that version did better, thanks to the spacer on the big gear). All the...
cults3d
It turns fairly well now, as you can see in the video of it turning here: https://www.instagram.com/p/BuXiaIwH_OG/?utm_source=ig_web_button_share_sheet You'll have to grab the heart gear parts and base from either the original or the one linked in...
thingiverse
It turns fairly well now, as you can see in the video of it turning here: https://www.instagram.com/p/BuXiaIwH_OG/?utm_source=ig_web_button_share_sheet You'll have to grab the heart gear parts and base from either the original or the one linked in...
prusaprinters
Proof of concept, it doesn't really move much air - hand cranking at a reasonable pace, you can feel a little bit of movement. ...1:8 gear ratio seems to be a bit of a sweet spot, but there's likely too much friction to chain two of these planetary gear...
thingiverse
... with 2 screws. ...This gear have teeth made of half-circles and extra holes to save materials. Instructions Take a round stick of wood, D = 28 mm. ...Fixate the gear on the round stick with 2 screws.
thingiverse
Instructions Print the original heart:http://www.thingiverse.com/thing:12208 Print one of each stl of this thing; Print the remaining things from:http://www.thingiverse.com/thing:253934 Assembly: The same as original crank thing plus: heart base top...
prusaprinters
Some teeth of the large bevel gear had broken in our hand cranked potato peeler so I had to make this. ...Our potato peeler happened to be of a brand Valentini, but other brands seem to exist too.</p><p>I printed it in Prusament PLA with 0.2 layer...
myminifactory
......Her husband Marc, after seeing the "Geared Heart, Hand Cranked Edition", asked my wife if I could make her an OSU (Oklahoma State University, her Alma Mater) colors version of the "Geared Heart, Hand Cranked Edition" that was easier for her to hold.
cults3d
......Her husband Marc, after seeing the "Geared Heart, Hand Cranked Edition", asked my wife if I could make her an OSU (Oklahoma State University, her Alma Mater) colors version of the "Geared Heart, Hand Cranked Edition" that was easier for her to hold.
thingiverse
I wanted a Z-axis hand crank, and had already printed this wicked extruder gear - so, naturally, this happened!
thingiverse
Then came Geared Cube, Hand Crank Edition by gzumwalt. This is more rugged version of gzumwalt's model. Designed in MOI, printed in Diamond Age PLA on an Ultimaker 1. A short video is here: http://youtu.be/quQQPeJRWsE Important Note. To make this...
thingiverse
I made a hand-cranked gear. M3 screws can be used. ... Ratio 6.25 Upload 2020.11.08
thingiverse
One of my hand cranks broke and epoxy didn't fix it so I took the measurements and designed a replacement. The replacement I designed now has a double handle but it's easy to delete the second crank from the OpenScad file if you want it more like the...
thingiverse
This object when printed is cranked to create a continuous sound of scraping plastic. The arm is designed to barely overlap the extrusions in the cylinder. Post-Printing The arm and the crank should fit together. ...You can use glue to hold the cap if...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: MusicCylinderNamePosition = 0 crankAxisHolderH = 1.55 gearH = 3 MusicCylinderNameDepth = 0.6 MusicCylinderName = test song midBigTeeth = 20 E_PLA...
thingiverse
A simple hand crank fan with 3 spur gears and 2 bevel gears. ...Can be built completely with 3D printer.