hand powered usb charger 3d models
242158 3d models found related to hand powered usb charger.thingiverse
Basically it's designed to be a wind powered USB charger. It harnesses the power of the wind, and uses a small motor to turn it into electricity. For those who don't know, motors and generators are essentially the same devices. If you put...
thingiverse
... Made 19mm and a 21 mm shaft, so the motor is kept tight in place. Motor and USB-port are not generating any power yet, but with some trial and error I'll hope to make it work upcoming few days. ...But if you have any suggestions, please let me know.
thingiverse
This is a Lipo powered portable USB charger. There are two versions. Single port and dual port. You will need an XT60 connector (available online or at most RC hobby retailers) and the USB charger module. The link to the specific charger module can...
thingiverse
Search for "TP4056 USB Li-ION Battery Charger" to find a provider on the net. Spring was retrieved from an old battery holder. There is a small slot to hold and block the spring. For the positive side, strip the cable on 2/3 cm, make a small ball...
thingiverse
As charging circuit I use a TP4056 USB Li-Ion battery charger breakout. ... Video: https://youtu.be/LuD-b34_SiA Blog: https://ewap.ch/elektronik-3d-drucken/ Instructables: (coming soon) Affiliate Links, if you need something: Charger circuit TP4056:...
cults3d
As charging circuit I use a TP4056 USB Li-Ion battery charger breakout. ... Video: https://youtu.be/LuD-b34_SiA Blog: https://ewap.ch/elektronik-3d-drucken/ Instructables: (coming soon) Affiliate Links, if you need something: Charger circuit TP4056:...
3docean
USB power charger with cable for smartphones detailed 3D all used materials are included .3ds/.skp/.obj/.fbx
thingiverse
I bought a [USB-Charger with Power-Sockets](https://www.banggood.com/LDNIO-5V-3_4A-Desktop-3-Power-Socket-6-USB-Port-5_24ft1_6m-EU-Plug-Charging-Socket-p-1091697.html?cur_warehouse=CN), but it was not possible to hang on the wall. With this is it. ...:)
pinshape
... you do not have a phone charger with you! ...You can enjoy music, gps, even tracking your exercise!! Printing currently, more pictures to come. The "crank generator" can be a simple hand cranking generator attached to it that allows for USB plug ins.
thingiverse
519/5000 it is a housing for a USB power supply board for two ports, in which the USB connections are horizontally side by side. The circuit board is from a Wicked Chili dual USB car charger. I used three different models. Model: 24800 Vers. 4.0...
grabcad
just to fill time A USB Charger by My selves Enjoy it, comment are welcome Thanks :)
prusaprinters
The output USB does not currently support any protocols to switch the voltage, so the output USB port remains at a constant 20v. The schematic part list can be found in the schematic, but other parts are required (but can be had for cheap). XT60...
thingiverse
The output USB does not currently support any protocols to switch the voltage, so the output USB port remains at a constant 20v. The schematic part list can be found in the schematic, but other parts are required (but can be had for cheap). ... XT60...
thingiverse
at http://mekatronikgruppe6.wordpress.com Printable parts for a hand held, and hand powered dynamo. The motion of you hand powers a diode. This dynamo is made as a project at the course Mechatronics Engineering Design at Technical University of...
grabcad
Open-Source Files FINAL ASSEMBLY FILE MISSING Assembly instructions at: http://www.instructables.com/id/Galileo-Hand-3D-Printed-Prosthetic-Hand/ This version uses body power to activate/control the grasp, all the components are low cost and should be...
thingiverse
https://youtu.be/P4YJBCraq5k This HPL (hand powered light) uses a cheap AliExpress geared DC motor. It supplies enough energy for a 100 mA led (white, 10mm). The basic circuit has a resistor and led, that's all you need to make light. A 1000uF...
thingiverse
Under-shelf mounting bracket to hold 6-port RAV Power USB Charger. Additional hardware needed: Four 3/4 inch self-tapping (sheet metal) screws. ... The bracket mounts on the under-side of a shelf and holds the USB charger in place.
thingiverse
This is a hand powered fan. It spins using a finger tapping motion. It was created in Tinkercad and printed in ABS on a Flashforge Creator Pro 3D Printer. The fins are only small so it doesn't move a huge amount of air. But it's a fun desk toy...