handheld console display stand 3d models

Post-Printing Assembling the device To assemble it, start by mounting the stand to the table, followed by attaching the backplate to the stand, and finally installing the front panel onto the backplate. The bottom of the stand is 5mm thick; a 5x20...

A basic stand for displaying K'Nex models. There is a slot for an orange KNex connector. Once you slide the connector into the slot, you can attach any of the bars by sliding into one of four holes and it will hold the bar in place. This may take...

Spinning Reel Display Stand This stand is perfect for drying freshly rinsed reels or adding a touch of style to any room. To print the stand, all parts should be laid flat on the bed with the arms facing up. Please refer to the slicer photo for more...

This display stand accommodates large knives, featuring a knife 15 inches long. Measuring 4.3 inches wide by 3 inches deep by 1.4 inches tall, the base provides a stable foundation for the stand. Assembled, the entire stand stretches 6.8 inches in...

Turn Table Stand

UNICORN GUNDAM TRANSFORMATION STAND

Cool machete stand.

Important Note: When assembling this display stand, please pay close attention to two critical details to ensure a seamless experience. Firstly, when attaching the watch cushions, take note that the rod passing through them is slightly loose. This...

I designed a display stand for my Tungston cube, allowing me to showcase its unique features. The base measures 2.5 inches in diameter, perfectly accommodating a 1.5 inch cube while providing room for larger or slightly smaller cubes as well. Its...

This is a 3 tiered stand I made for displaying funko pops! The design is specifically for my bookshelf, however I imagine it will work for many different bookshelves. The design is 280mm wide, 265 mm deep and 175 mm deep, and should hold about 12 out...

I'm a woodworking enthusiast who creates custom knife handles and has experimented with various display stands. Previous attempts to print similar designs didn't meet my expectations, so I designed this compact stand myself. Its size allows for an...

The Hellboy PROP Gun model designed by Dan0nator is a standout piece that warrants a display stand of its own. To enhance the print's stability, I've included both a stand with helper tabs and one without them. The tabs serve to prevent the print...

From the Applied Sciences Division of WayneTech, Lucius Fox presents a custom display stand for ThatTTUGuy's Dark Knight Batarang (http://www.thingiverse.com/thing:26130). This is part of a comics-themed bedroom series for his son and features a...

The display stand was designed to be hollow with no bottom layers and 0% infill, ensuring it remains lightweight while preventing warping. To achieve this, I added a brim during printing. I used PLA and PETG filaments, which provided excellent...

This is a generic display stand for replicas of guns compatible with diferent kind of guns. I have a friend that collect replicas of historical and actual guns and want to display them properly. He has a similar display like that but need some...

... would complement each piece without drawing excessive attention away from their natural beauty. To achieve this, I drew inspiration from an acrylic stand I had previously used, but with some key improvements to balance aesthetics and functionality.

A display stand in standard and compact versions is available. This stand is highly versatile and can be printed to any size required! It's ideal for displaying CDs, or large enough to showcase pictures, books, etc. Printing proceeds quickly! I use...

I did 5 minutes of research and decided I didn't like any of the display stands for pens, so I made my own. ...The pens I make end up being a tiny bit big but they just barely fit.(edit) I've remade the same thing but made the racks a bit thinner so...

... screws to combine. Figure Display Stand, Measure just under 8" at 194mm with maximum figure stance of just under 5" at 124mm. Can accommodate a 60mm diameter x 8" thick puck light for lighting effects. ... Will require supports everywhere enabled.

... It comes with two larger side spots for short fixed blades, sharpening stones, lighters, or any other EDC items you would want to display. I cut a decorative curve into the top of each knife slot, which looks pretty rough at 0.3mm layer height.

This is a display stand for the original Game Boy, works with or without a battery cover. ... If you want to make a Kit you will need 2x 1/2" 10-32 machine screws and nuts If you don't have a 3D Printer I can make it for you from my stores on eBay...

... work just fine. Modified the stand I made for the CZ P10 series to fit the bigger glock mags and made the peg a little larger to make the pistol fit slightly more snug. This should still go on easy! ...If not let me know so I can adjust it :)

Here is the text with a rewritten tone and phrasing: This sleek 25mm miniature display stand makes showcasing your tiny treasures a breeze. Its precision-cut slots measure exactly 26.5mm, ensuring a snug fit for tapered miniature bases of all shapes...

This is my rendition of a recent Oakley sunglass display stand. My version uses 6-32 machine screw hardware for the upper "hoops." I could have created this to completely snap together, but it would have consumed much more time. My total CAD...

I wanted something to display my old Gameboy Advance and the games I grew up playing, so I designed this stand. The only place it needs supports is the empty space directly under the Gameboy. I made it to hold the exact number of games that I own,...

This Keychain Display stand is great for modeling any item that may be a bit too fragile to carry every day. Seen here with a time turner from this listing: https://www.printables.com/model/503392-harry-potter-time-turner-print-in-place The Hoop fits...

We've gone so far as to even design things like this - a Pocket Knife Display Stand. It's simple, and it works. This thing will hold four Lander 1s without breaking a sweat. ...The question is how many knives will you cram onto yours?Designed by Matt...

I put together a quick and easy display stand for these hygrometers I have been using. All that is needed is an M3 50mm bolt and nut (as the hinge). ... As far as I can tell, the size of the hygrometer is pretty standard, but The ones I have are: ...

Here's a fresh take on OzzytheMozzy's Display Knife Stand, reimagined from the ground up. The curves of the surfaces and edges have been refined for a sleeker look. This updated design is more streamlined, with a shallower groove to hold the blade in...

A Gameboy cartridge display stand for games with protection enclosure.You need to place the bottom face to your printing bed in your slicer (e.g. ..."Face on plate" in PrisaSlicer) because I used the top face as the base plate in FreeCAD.Note: The...