hanger holder 3d models
340471 3d models found related to hanger holder.thingiverse
We like to store the empty hangers there as well, but if they're hanging directly on the rod they get in the way of closing the door. ... I created this quick loop that goes over the rod so the hangers will be parallel and out of the way of the door.
thingiverse
This hanger holer design is made in 2 parts. The target was: to not use support during the printing. Dimensions: Height: 134 mm (5.27 inch) Base: 90mm x 45 mm (3.54 x 1.77 inches) Holes diameter: 5mm on the base and 3mm for the top. The...
thingiverse
Clothes hanger holder for 5 pendants 2 Versions, a small version and a version with more space
thingiverse
Coat hanger holder for closet door to dry washed hoodies or hang other clothes. ... Part that goes over the door is 19mm.
thingiverse
I created this hanger/holder for my bathroom. It is easy to print and mount. It has six (6) hang/hold points! ... I hope it will be useful for other people too!
cults3d
I created this hanger/holder for my bathroom. It is easy to print and mount. It has six (6) hang/hold points! ...I hope it will be useful for other people too!
thingiverse
A 3D printed hanger holder that slips over the generic plastic hangers that you can find at most stores. Has a slot on each side for 2 more hangers to hold onto. ...My current setup can hold medium to heavy clothing.
thingiverse
... nice to hang clothes on doors, but we all do it a bit. ... So i have made this Hanger Holder and this is specific for my door. ... It is specific to my doors, but I have attached the Autodesk Fusion 360 file so that you can adapt it to your needs.
thingiverse
Be sure to check also my other DeWalt hanger holders: For DCD7xx Drill Gun - https://www.thingiverse.com/thing:3932084 For DCD991 Drill Grun - https://www.thingiverse.com/thing:4198707 For DCF680 Screw Driver -...
thingiverse
If you wish to hang your DeWALT DCD991 (or maybe others DCD99x) drill gun also with additional stick, you're on right page :) Be sure to check also my other DeWalt hanger holders: For DCD7xx Drill Gun - https://www.thingiverse.com/thing:3932084 For...
prusaprinters
Now you can hold it under shelf or workbench! Be sure to check also my other DeWalt hanger holders: For DCD7xx Drill Gun - https://www.thingiverse.com/thing:3932084 For DCD991 Drill Grun - https://www.thingiverse.com/thing:4198707 For DCF680 Screw...
thingiverse
Double shower shaver hanger / holder for Gillette The diameter of the rod in the bathroom is 4mm.
thingiverse
Umbrella Holder/Hanger to suit Audi A4 and VW Passat (Saloon) May fit other cars. ...Bolt and Nut need to secure it to the car.
thingiverse
... something shorter so that I could mount it between my storage shelves. I removed the drill portion from the bottom of the hanger, and printed the battery holder and drill hangers separately. This allowed it to fit well in my available space. ...
thingiverse
I've printed it with supports, and added a modifier in Slic3r for the little hangers so the infill is higher for extra strength. ... I've added two versions - regular and with voronoi - if you like saving your material ;) Screws used are 3,5 mm...
thingiverse
Add this clip to your washing line to hold clothing hangers. ... Prevents hangers blowing off the line. Stops hangers sliding together. ...
thingiverse
Simple wall hanger for my multimeter. ...Internal dimensions are 73x36mm.
thingiverse
A simple but useful headphone hanger. ...Designed especially for SONY WH-1000EX3.
thingiverse
So I designed a holder/hanger that the drill nicely slips into like a holster. Then I mounted it under my desk against one of the uprights so I could snatch it out whenever I needed it. I'd love to say for sure what drill model number the holder...
thingiverse
I needed simle cable hanger so I designed one. Very simle yet strong. ... Hole is for hanging on a nail or you can just use double-sided tape.
thingiverse
You can also hang your clothes with the bottom triangle using a hanger. Mounted with 5mm diameter wall screws. Printed in PLA with 20% infill using a raft. *updated* The holes were too big and I didn't notice it at first. ...Now I think it works...
thingiverse
I created this socket wrench hanger for my dad, maybe you will also need it. If my project was useful, leave a like :) Just use "Standard Quailty" Cura print profile. ... Tip: If the print does not fit, place the model diagonally in Cura