harbor freight lights 3d models

I broke the mount for my harbor freight light and there were no designs for the part I needed. It is for the Bunker Hill Security Light. ...SKU # 64736 and 64735.

This go pro mount makes the Harbor Freight FREE light the perfect headlight for your Bicycle.

This is a light bracket that will hold a Harbor Freight LED light bar on a Creality CR-10s. I printed this with .2mm layer height and 32% infill for strength. ... NO supports.

harbor freight solar light stake

I created this to mount the little Harbor Freight LED light to the ceiling of my UTV. I use zip ties to mount this to a bar and then snap the light into it. This was my first creation from scratch done in TinkerCAD. ... I am fully aware that this...

I have several of the freebie LED lights from Harbor Freight lying around (https://www.harborfreight.com/2-piece-3-12-in-led-mini-flashlight-63600.html), so I thought I could make up a clip that would hold the light at the top of my Ender 3. The...

IDK about anyone else, but I have more than a dozen of those free Harbor Freight blue flashlights, so I decided to put them to use. I took one apart & designed the light pod to fit the LED strip in it. But when taking apart more, I found out there...

Wall Mount I made for the Harbor Freight Rope Light Solar Piece. ... I tapped the two holes with a 6-32 tap, print with at least 4 top/bottom layers and 3 shells.

These Harbor Freight Flip Lights are bright and only $3.99, so I whipped up a rail mounting system for it. You will lose about 30 mm or so of print height, but it is installable and removable without tools. Print laying flat for best results. I...

hanging shop lights that you can get at Harbor Freight. I don't like hanging these from chains as intended, so I made these so that they become more of a permanent fixture. Since the cord exits the top of the light, there are two versions of this...

Link for light-https://www.amazon.com/Lumens-Bright-Harbor-Freight-64189-63922/dp/B07D5JCBW4/ref=sr_1_6?dchild=1&keywords=harbor+freight+switch&qid=1586535644&sr=8-6 THIS LIGHT IS ONLY FOR LIMITED TIME USE, NOT TO LEAVE ON!! -You will not need any...

If you use the harbor freight led light strip you dont have to do any hard wiring and it has a cool IR remote that lets you remotely change the colors. I also resized 2 of them to 140mm(sides), and 1 to 160mm(top) that allowed them completely fill...

If you use the harbor freight led light strip you dont have to do any hard wiring and it has a cool IR remote that lets you remotely change the colors. I also resized 2 of them to 140mm(sides), and 1 to 160mm(top) that allowed them completely fill...

light holder for Braun (Harbor Freight) 5000 lumen led light bar. ...I recommend 3-6 per light fixture but i have not yet printed this yet

Template to locate the screw mounting holes on the harbor freight bright lite switch.

This is a remix of the wonderful Lithophan box by garyp53 that allows a harbor freight LED puck light to act as the light source (sku 64593). I have printed this and the puck light fits perfectly, however, im not sure how it will work as the light...

... printed in spiral or vase mode to save filament. ... It should allow Harbor Freight and similar flashlights to use a 18500 battery without it rattling around inside the flashlight. ... You can find 18500 batteries on Amazon, Ebay and most battery store

... ... Instructions Print and break off the "support" piece in the center of the screw hole (note this was designed for a 0.4 mm nozzle). Mount accessory or GPS in place of the light on the handlebars.

Customized version of http://www.thingiverse.com/thing:92149 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=92149 Instructions Using the following options: num_grips...

Replaces the 3 AAA Batteries (Holder) with a 18500.....

This is a body and back plate to combine two of the Harbor Freight work lights that you can often get for free with a coupon. It uses the lens, LEDs, and screws from the original lights. I built this to film night fishing, but it could easily be...

This is a body and back plate to combine two of the Harbor Freight work lights that you can often get for free with a coupon. It uses the lens, LEDs, and screws from the original lights. I built this to film night fishing, but it could easily be used...

There are some designs for older Harbor Freight Braun-branded shop lights, but they didn't work for the lights currently sold at the store. These allow mounting the lights flush to the ceiling (Light Holder A & B) or mounting spaced about 25mm out...

I needed a specific size for a Harbor Freight product and modified to work perfect. The file is horizontal and needs support to print and worth the added filament for great strength printing horizontal. I printed at 15% fill, raft, and support in...

... I want it. This little attachment clips on the bottom and acts as a stand. I integrated a flat so it can be pointed any direction when it lies on its side. It snaps on the base of the light. ...Mine was a tight fit, but it went on without breaking.

For the light bar, m2s seem to be working, but likely not correct. Update 11.6.21. Found some much better gripping design. Thank you to https://youtu.be/mXsIO7a7ZVo, otherwise I would have never got it unscrewed. Also, thank you to...

This is a snap on cable management plate for the front (above the door) next to built in 5v USB Port with provisions to slide in a an LED pulled out of those free harbor freight flash lights. Most people have these laying around and it gives off at...

This is a bracket for the updated Harbor Freight Braun 5500 4' Shop Lights. Only two are required to hang the light, one on each end. ...The bracket is extra sturdy and can easily support the light.

I bought a Four-Head LED light set from Harbor Freight ( https://www.harborfreight.com/four-head-led-under-cabinet-light-62902.html ) to mount on my Wanhao D9/500 printer. They are battery operated and since the heads can be adjusted I am able to...

I bought a Four-Head LED light set from Harbor Freight ( https://www.harborfreight.com/four-head-led-under-cabinet-light-62902.html ) to mount on my Wanhao D9/500 printer. They are battery operated and since the heads can be adjusted I am able to...