hard drive sled macbook pro 3d models
156934 3d models found related to hard drive sled macbook pro.thingiverse
So after printing a case for my banana pi using the thingy (http://www.thingiverse.com/thing:629473) I found that I could use a place for a 2.5" hard drive to be stored. So I created this sled. Maybe some one else will find it handy as well. The...
thingiverse
I made this to hang my hard drive on the back of my Macbook so that it wouldn't be lose. the file labeled 2 was a little to tight and had to be sanded. and the file labeled 3 worked pretty well but could be a little tighter. ... I am currently using...
thingiverse
... for some reason. ...Fortunately I had another one handy to make a copy of. Hopefully this will be of use to someone else too. I printed it in 100 percent infill and it only took a few minutes to run off. Works perfectly. No more flopping hard drive!
cults3d
... for some reason. ...Fortunately I had another one handy to make a copy of. Hopefully this will be of use to someone else too. I printed it in 100 percent infill and it only took a few minutes to run off. Works perfectly. No more flopping hard drive!
pinshape
... for some reason. ...Fortunately I had another one handy to make a copy of. Hopefully this will be of use to someone else too. I printed it in 100 percent infill and it only took a few minutes to run off. Works perfectly. No more flopping hard drive!
thingiverse
I fixed the model by recreating it in Fusion 360 as well as adding the cutout for the case locking mechanism.
thingiverse
This is a Remix of E_Roth_3's hanger, I wanted it to fit tight to the screen so when I carry the laptop the drive does not easily come off. ...This was created for the Passport style drives, with external dimensions of apx 82mm x 20mm
youmagine
Data Doubler to replace your DVD CD Rom drive in your Macbook with a second hard drive.Best printed in ABS or Nylon. I have not tested with PLA. Infill 20 - 25%.Will require a Slimline 13 pin SATA Male to 22 Pin SATA Female Adapter from...
thingiverse
This is 3.5 inch drive sled for a Cyberpower Dragon Rider case. ... Note I used heat to bend the tabs in the approximate location it needed to be angled to.
pinshape
I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF 5.25" optical drive SFF-8851: ftp://ftp.seagate.com/sff/SFF-8551.PDF You can print either a full sled with a base plate, or just...
thingiverse
I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF5.25" optical drive SFF-8851: ftp://ftp.seagate.com/sff/SFF-8551.PDF You can print either a full sled with a base plate, or just...
thingiverse
Hard drive sled for IBM PS/2 models 76 and 77. ... The IBM FRU numbers for the original sled are 96F7775, 71G5706, 71G5708, 79F3300 Hope it helps someone :) 32K
thingiverse
Wanted to add a hard drive to my Mac Pro but was missing the bracket tray. Doubt many people need it, but here it is! It's a little flimsy but fit perfectly, just need to guide it in underneath. ... Might add a 2.5 inch one later as well.
thingiverse
This is a hard drive sled for mounting 3.5" and 2.5" hard drives in a Cooler Master CM 690 III case (aka CM693). The original drive sleds are adjustable to fit either in the 3.5" bays or 2.5" bays. Since the upper bays can be configured to be either...
thingiverse
This is an adaptation of the parametric drive holder that can accommodate two different types or sizes of drives (and any number of them) Default settings are for 1x 7.3mm thick 2.5" SSD, and 1x 26mm thick 3.5" HDD. Drive 1 must be the smaller of the...
thingiverse
Features a tool-less design with a retaining pin to hold the drives in place without screws, but screw holes are also provided if you need to secure them. Default values are for 4x 7mm SSDs. Can work for 2.5 and 3.5 inch drives. Adjust the...
thingiverse
3.5" to 2.5" adapter for PC drives. ...May not work for certain configurations. Designed to adapt drive sleds from 3.5 to 2.5 for facilitating an SSD upgrade on an older machine.
thingiverse
If you have Mac Pro and in lack of a missing drive sled, you are in the right spot! The dimension are derived from the original bracket and compatible (tested) with following Mac Pros: Mac Pro 2009 to 2012 Model Identifier: 4,1 and 5,1 If you need a...
thingiverse
This is a replacement hard drive slide for IBM PS/2 models 50, 50Z, and 70. The IBM part numbers are 90X8546 and 90X8628 (the real sled has both numbers molded into it). ... Use supports when printing.
thingiverse
I was rebuildin my Plex server but I was out of the drive sleds so I made my own
thingiverse
# Dell PowerEdge Screw-less Hard Drive Carrier Needed a simple hard drive carrier for my server. Did not want to pay, and _did not want to use screws_, so I printed one. ... ## Check out the vertical stands on [here](coming soon) ## F360 and...
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
grabcad
its a hard drive from kingston. ...its a case where you can put in hard drives from old computers/laptops likes are appreciated