hard drive storage case 3d models

This is a hard case for 3.5 inches hard disk drives. Designed to be stored horizontally (I store them upside down). You will need some felt pads, the ones I used are 3.5mm thick, roughly 1/8". ...You can change that value in the file, though, it is...

Customized version of https://www.thingiverse.com/thing:5479913 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5479913

Customized version of https://www.thingiverse.com/thing:5479913 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5479913

Customized version of https://www.thingiverse.com/thing:5479913 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5479913

Customized version of https://www.thingiverse.com/thing:5479913 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5479913

14-bay 2.5" Laptop Hard Drive Storage Case holds both 9.5mm and 12.5mm-thick drives. Five slots accommodate larger 12.5mm HDDs, nine spaces fit 9.5mm HDDs comfortably. ... Ideal for mounting on a desk or workbench.

------------------------------------------- 2.5" HDD cases used: https://www.banggood.com/ORICO-2139U3-CR-2_5-inch-Type-C-Hard-Drive-Enclosure-p-1109914.html...

FR _ Hello Here is a simple storage for multiple hard drives. It can be used vertically. Print as many elements as there are hard disks and a cover. Each element can be nested and glued together. ENG_ Hello Here is a simple storage for several hard...

Provides long-term or transportation storage for four hard drives. Feet can be printed and inserted into the feet slots in the bottom to provide cushier surface contact and make the storage cages stackable. While I printed the feet in TPU, you may be...

This compact enclosure securely holds multiple hard drives, its sturdy design featuring precise notches at the top that allow for effortless stacking and organization.

... body and the box, you can print them upright. I used buildplate supports for the enclosure body, but honestly, my printer could have bridged just fine. This is gonna be the best hard drive enclosure you've ever seen, folks. ...Trust me on this.

I have a stack of 16 HDD's currently (and growing) and wanted a way to easily pull a drive out of the stack whenever needed. These trays are modular and extremely versatile. The pins on top slide into holes on the bottom with ease, allowing me to...

12 3.5" hdds, 9 2.5" ssds and 9 USB drives fit Dividers are 3mm wide so i printed it with 1mm line width and 3 walls so it printed the dividers solid, 10% cubic infill is fine it only uses a little infill under the 2.5" and usb drives. ... If you...

hard drive case

Stackable hard drive storage rack

Human: For Multiple High-Density Hard Drive Storage Enclosures

Toshiba External Hard drive case. ... Suits: Toshiba 1TB Canvio Basics Portable Hard Drive Black Toshiba 2TB Canvio Basics Portable Hard Drive Black

This is a protective case for a Western digital Hard drive. Printed in TPU. ... There is an opening on the side to add the Wire

Constantly swapping the hard drive caddies between the different sets became cumbersome, so I purchased a set of caddies for each set of hard-drives. Then I found there were no existing products or models to use as a storage container. Enter...

This is a protective case for a Western digital Hard drive. Printed in TPU. ... There is an opening on the side to add the Wire How I Designed This Fusion 360

This sturdy external hard drive case is specifically designed for housing two hard drives, each neatly compartmentalized within an area of 85mm x 15mm. Its versatile design allows it to effortlessly hang on either a monitor or laptop, making it the...

This is a simple case for hard drives with the standard size. The top pieces of the case fits very tight, so when you are unable to close it just sand it a little bit until it fits. I printed everything without supports in my normal settings. ...Be...

Hard drive case for both 2.5" and 3.5" HDDs. Has holes for screws to prevent the hard drive from moving around, a removable lid, and locks to hold the lid in place.The red one is 2.5" and printed in Polyalchemy Merlot and Natural Elixir. The white...

A handy individual safely secures their hard drive once removed from its laptop home, potentially paving the way for an SSD upgrade. Carefully crafted with Tinkercad's intuitive design tools and reinforced using Net Fabb's repair features. Detailed...

Construct an affordable external HDD by utilizing a 2.5-inch hard drive enclosure. Fasten the drive securely using four M3x4 screws. ...Easily print without support, and attach via USB with a Seagate adapter.

Storage trays that were designed for storing laptop hard drives in my collection. Print instructionsNo need for supports.

Enclosure for 2.5" hard disks, can hold up to 9 hard disks. In my case I have glued the parts together with super glue. ... Contact me if you have any questions: jmdrblue@gmail.com

Here is the rewritten text: A protective housing for a compact 12-centimeter (five-inch) hard drive, designed using SolidWorks, poses a minor challenge in Part 2 regarding the placement of the connector.

... of the night, got to thinking. ...Thought about making this, so I did. Haven't printed it yet, so if you do please let me know how it turns out for you. The picture shown is the label for the case, it should be printed to a size of 5.5 cm x 9.7 cm

A first attempt to design an own thing as others sadly havent fit my drives, so making them stackable and quite light weight, easy to print and little consumption of material was a nice goal. Feel free to use it, mod it, print it, trash it, take...