hasselblad 500 strap 3d models
35679 3d models found related to hasselblad 500 strap.thingiverse
custom made camera strap lug, holes for actual strap are a bit tight but work and beat spending a ton of money for such a simple piece. ... Instructions i used a fill of 50% to get the right strength in...
cults3d
A reproduction of the beautiful Hasselblad 500, a medium format film camera made by Hasselblad and produced in the 60s. Fully 3D printable. ...Remember to Scale and Print
thingiverse
Hasselblad strap lugs, suitable for Kiev-88 (tested on this camera), Salyut, maybe Mamiya (not tested) Easy to print, does not require supports, high strength, minimalistic design I was not satisfied with the strap lugs on the thingervers, and the...
thingiverse
Don't want to pay for an expensive Hasselbald strap, plus I want to use my own favourite straps so I've decided to design one myself. Print Settings Printer: FlashForge creator Pro ...
youmagine
A lock for the Hasselblad 500 EL/M Batterydoor, that doesn't need a coin or screwdriver to open. ...You can use the folding handle instead. Prints perfect with Ultimaker on highest quality setting, with reduced speed of 25mm/s and additional cooling...
thingiverse
A battery adapter for USB for the popular Hasselblad 500 EL/M V-System camera. There are a few expensive battery adapters on the market that use AAA-batteries but this one uses USB power from a powerbank to power the camera. The principle is to...
thingiverse
These are masks to place against the curtain on the back of the body of a V series Hasselblad to capture 645 images (in either portrait or landscape orientation) and 6x3 "panoramic" images. I printed and sanded down to exact fit for my camera. ...These...
thingiverse
This is a 3d design of a Hasselblad that Im planning on making into a pinhole camera. Instructions Print out the camera. Drill a slight hole (1/4\") directly in the center of the lens, put a piece of...
thingiverse
This is a holder for Wetplates on a Hasselblad 500 or Kiev 88. ...You need the darksheet from a film cassette und four magnets 5mm diameter and 3mm height.
thingiverse
This low profile adapter is solely optimized for the Lime Two light meter to be mounted on a 500 series Hasselblad camera. ...If you want to use it with other accessories you probably have to adapt the STL Update July 2023: current updated variant!
prusaprinters
Template for (laser-)cutting your own replacement leatherette for the body of an old Hasselblad 500 EL/M camera. Print instructionsWhen lasercutting thin leather, I'd recommend taping it to a piece of MDF using double-sided tape, so it wont curl,...
prusaprinters
This is a custom made handle/battery-door lock for the Hasselblad 500 EL/M, which does not require a coin or screwdriver to open. Print instructionsPrinted the parts using PLA with a layer height of 0.2mm. The holes in this design are the tricky...
thingiverse
A replacement for the plastic screw-like part of a Hasselblad 500 EL/Ms battery door. Instructions This was created by measuring and a lot of trial and error. After my battery door was blasted off by...
thingiverse
Template for (laser-)cutting your own replacement leatherette for the body of an old Hasselblad 500 EL/M camera. Instructions After I got lucky to win the auction for an old Hasselblad 500EL/M in good working condition, I went to replace the...
thingiverse
This is a custom made handle/battery-door lock for the Hasselblad 500 EL/M, which does not require a coin or screwdriver to open. Update: Added new version of knop with slightly bigger hole to improve fit. Prints perfect on Ultimaker with 25mm/s...
youmagine
Template for (laser-)cutting your own replacement leatherette for the body of an old Hasselblad 500 EL/M camera.I measured the whole camera using a simple ruler and a lot of guesswork and recreated the dimensions and shapes in Inkscape. After lots of...
prusaprinters
The dark slide snaps in place in the holder.Clip the holder on e.g.Shoulder strapsBeltsCamera bag dividersPocketsetc.------------------------------------------------------------Print in the default orientation without supports. Use brim if...
thingiverse
Viewfinder mask for the Phase One H20 and P20 digital backs when used on a medium format Hasselblad V system camera, like the 500 C/M, the 500 EL/M, and many more models. The H20 and P20 both use Kodak's KAF-16801CE sensor with a dimension of 36.9...
thingiverse
print for dm 56 aptus II-56 thick:1mm also have about 48x36 see my other
thingiverse
Viewfinder protective cover for Hasselblad 500 series cameras.
thingiverse
Camera Hasselblad 6x4.5cm Mask for the 500 C/M Not a lot else to say.....
grabcad
Hasselblad X1D-50C Medium Format Digital Mirrorless Camera with Hasselblad XCD 90mm F3.2 Lens
thingiverse
I nearly bought two hasselblad CT* lens but have neither caps. ...I did not find B50 cap here so I deside to make myself.
thingiverse
hasselblad V mount body cap Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: No Resolution: 0.3 Infill: 30
thingiverse
A cover for the Hasselblad exposure knob; I printed mine in TPU, 20% infill. Hope it helps someone! Have a nice time with your Hassy! ...;)