hatchbox filament 3d models
174934 3d models found related to hatchbox filament.thingiverse
Spool bushing for hatchbox filament rolls. Bearings are pressed in on both sides and I used Duralast part# 201-CC. ...Found at autozone for $1.99 each.
thingiverse
This is a Hatchbox filament holder for the anet a6 printers. ...It attaches using the screws used to put the printer together and it goes right next to the power supply.
thingiverse
This is a pair of inserts to be used with 6806 bearings, the Hatchbox filament holder, and Hatchbox filament. It should fit snugly and provide a smooth, low friction filament holder instead of a jerky motion from the extruder stepper pulling...
thingiverse
I have a Hatchbox Filament Spool on my Anet A8. The provided spool holder has a screw and the spool has a large hole so the spool doesn't rotate well. ...This coupler connects the spool holder and screw so it can rotate easier.
thingiverse
Adapter for using hatchbox filament with cr-10 spool.
thingiverse
An adapter for Hatchbox filament spools, so they roll nicely on the CR10 spool holder. ...
thingiverse
I remixed Tech2C's spool holder to fit the Hatchbox filament I purchased from Amazon. I don't recommend the filament, as it did not print well for me but for those who already have it, this is a spool holder that fit it. Customized version of...
thingiverse
These boxes are inserts for organizing small parts inside Hatchbox filament boxes. These are designed to fit 4x4 in the box so you can do any combination of sizes that adds up to that. This is a great accessory for the shelves/drawers I designed for...
thingiverse
Spool holder for Hatchbox (PETG) filament. I use this with an IKEA Lack enclosure for a Prusa printer. ... Links to Fusion 360 files: spool_axle: https://a360.co/2E5tKpf spool_axle_pin: https://a360.co/2E9PvEn spool_holder: ...
myminifactory
I ran into an issue with my filament bushing with hatchbox abs rolls. ...The old filament bushing did not fit so I reduced the outside diameter to fit the hatchbox spools.
thingiverse
Filament ruler calibrated for Hatchbox Spools. ...(Outside Diameter: 199, Inside Diameter: 80, Width: 61) Measure from the remaining filament to the outside of the spool.
thingiverse
This spool bearing is intended to adapt to a 3/4" PVC pipe and the Hatchbox branded spools. I reused left over 1/2" wooden dowel from my napkin holder project as a component. You can 3D print this component instead for better performance. ... I used...
myminifactory
The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. ... I used the following hardware to mount the bracket:Plate Support2x #4-40 x 1/4 Socket Head Screw...
thingiverse
Snip any melted/deformed filament from the end, insert the plug from the inside of the reel and thread the filament through the plug. NOTE: Remove plug before printing or it may get hung on the filament. Included are two versions. ... The short...
thingiverse
Created to add less stress on the gears of my snapmaker 2 a350. ...Fits Hatchbox spool.
thingiverse
The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. I used the following hardware to mount the bracket: Plate Support 2x #4-40 x 1/4 Socket...
cults3d
The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. I used the following hardware to mount the bracket: Plate Support 2x #4-40 x 1/4 Socket Head...
thingiverse
This is to be inserted into the spool that hatchbox uses. I included the sldprt file in case you want to adjust the hole diameter to fit to different spool axles. Also, the ends of the teeth may need spaced to 68 mm. ...It is at 67 mm right now.
thingiverse
So I tried to find a fully printable drawer for my leftover hatchbox spools but I couldn't find one that worked. This one is similar to some of the other designs on here but works perfectly with my spools. There are little nubs at the top and...
thingiverse
This is a simple solution to aid with reducing force needed to rotate the filament spool by keeping the axis of rotation centered. ...Included is one with 15.8mm diameter hole, and a second with 8mm
thingiverse
This is an adapter for the Creality CR-10s filament spool, for Hatchbox filament rolls.Normally the spool holder is so small it causes the filament roll to rock back and forth and put resistance on your extruder. ...This adapter will allow the Hatchbox...
prusaprinters
Some Hatchbox filament spool hubs I designed in SolidWorks for my Prusa i3 MkII. Hatchbox has two sizes of filament spools, and I made hubs for both sizes. ...Just print two of whatever size you need and one center rod and you're done.</p> Category:...
thingiverse
Some Hatchbox filament spool hubs I designed in SolidWorks for my Prusa i3 MkII. Hatchbox has two sizes of filament spools, and I made hubs for both sizes. ... Just print two of whatever size you need and one center rod and you're done.
thingiverse
... ...I glued mine for more stability but I don't think it is necessary. The holes you drill in the spool will depend on what paints you use. Please not this is made to fit Hatchbox filament spools, I am sure it can be altered to fit other spools.
thingiverse
STL files for printing inserts to transform empty Hatchbox filament spools into stackable wargaming terrain modules. Four inter-changeable "quarter inserts" can be selected to fill up the spool, while central tube sections run up the center of the...
thingiverse
Just a quick and dirty spool holder I made for a spool of Hatchbox filament so it would feed smoothly into the printer. I wanted to make sure I did not get any banding from changes in filament feed tension. FreeCAD design file attached (created with...
thingiverse
I mostly buy Hatchbox filaments and noticed that the boxes are pretty nice quality and are a great size for organizing small electronics parts and 3D printed parts. These use a lot of filament so you might be better off buying some cheap drawers at...
thingiverse
This is a simple adaptor I made for the original filament holder of the Anet A8 (and every other holder which uses a M8 threaded rod) Inner Diameter: 7,8mm Outer Diameter: 54,8mm Inner hole is a little bit tight but after some moving on the threaded...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069