hdd bay 3d models
10985 3d models found related to hdd bay.thingiverse
HDD bay for original DELL hdd caddys (the blue ones). ... Three versions for 1,2 and 3 HDD's.
youmagine
This jacket serves as a holder for a slim WD HDD.This thing makes a tight fit with the second hdd-bay on the caddy created by 3dGringo.DL from here: http://www.thingiverse.com/thing:410048The stl file does not include the small opening for the...
thingiverse
This is a dummy 3.5" HDD-sized box with sliding lid, to allow storage of expansion brackets, cables, adapters, and other computer accessories, in any empty 3.5" HDD bay. There is also a variation with dividers to create storage for screws and other...
prusaprinters
For example, here's the bracket installed in a Macintosh IIsi:Where can I buy one?Of course, you're welcome to print your own, but if you don't have a 3D printer, you can purchase a bracket on my Etsy store.PartsBlueSCSI 1.1a DesktopTwo M2.4 x 5 mm...
thingiverse
5x7 cm PCB in 3.5" HDD bay holder 2021-05-24 update: - enlarged drivebay screw hole - tweaked vertical position of mounting plate for better top clearance
thingiverse
Fan cover for Silverstone harddisk bay (CFP51) LOT more airflow, but less safety :) It looks cool but it's still possible to stick your finger into the fan blades so watch out for kids.
thingiverse
This is a remix of https://www.thingiverse.com/thing:1704615 CoolerMaster dual SSD bracket for 3.5” HDD bay The V1 version is that the SSD sit tighter inside the bay. ...
thingiverse
120mm fan adapter for Alienware R11 HDD bay. Remove the bay and replace with your fan clipped into this adapter. ... The clips are designed for Arcitc BioniX F120 fans
thingiverse
Adapter rails to mount two 2.5" solid-state drives into a single 3.5" HDD bay. Drives are offset to allow room for cables. Instructions Print both sides. ...Using the mounts on the underside of each...
sketchfab
Duel 3.5 Hard drive cage with 60mm fan mounted to draw radiated heat out.
cults3d
82.7 mm cover designed and tested to fit Dell latitude E6430. there is a cover that looks exactly like this model but it measures 72.7mm. make sure you check sized before downloading this. ...this model is the 82.7mm model.
thingiverse
A custom bay for 2.5 HDDs and SSDs Note: You'll need any 2.3 to 3.5 hdd adapter.
thingiverse
Remix of the double 5,25" bay PC computer to the external docking station for 3.5" HDD and SSD. Step file is temporary and not tested! Used on own risk. STL file is OK. No Raft and support needed . It is necessary to use the SATA Expander as it was...
thingiverse
So this is an adapter that I created to use with an Aleratec 1:11 HDD duplicator. The actual adapter from the manufacturer runs about $20 ea. After a few revisions I finally found what worked for me. I wanna say thanks to ComanderMuffif since I used...
prusaprinters
So not useable in regular case and probably also not useable for regular HDD holes. Print instructionsI printed it with PETG as I will have there 2 SSDs. ...But not sure how it will react, if all 4 with 2,5" drives are filled and used ( temperature...
thingiverse
This is V1 need to attached by side of the HDDs with 6-32UNC screws. ...Maybe in the next version will add the hot-swap function.
thingiverse
Made it more solid, removed the round areas, centered (didn't need offset side plugin for my use) and screw on standoffs. ...
thingiverse
I had been looking for a way to mount my Corsair Comander Pro in my Corsair 570X case without having to stick it in with double sided tape. Created a top and bottom mount with screw holes that match up to a 3.5 hard drive with routing channels for...
thingiverse
I made a new bracket because I wanted a split design; it means less long full surfaces and so less bowing, as well as a bit more tolerance as it does not depend on the cross-bar being the correct width and not shrinking. It is a little tough to get...
thingiverse
There's also space between the Pi and HDD to allow for air flow under the Pi and above the HDD. I modeled it to use fan screws for securing the fan and for securing the Pi/HDD carrier to the fan body. It will also work fine without a SSD/HDD. ... ...
thingiverse
A laptop bay for a second HDD/SSD: * height: 9.7mm * drive size: 2.5"
thingiverse
... Depending on your case you can maybe not use all the 5.25 bay screws but it should be enough to fassten one adapter because the 5 drives hold everything together. ... Drill the outer screw holes with a 3mm drill if they are to small after print.
thingiverse
Remixed the v3 version to have some chamfers and a more robust plate where you screw in the ssd (had problems printig it with 0,8mm nozzle), also made a slope at the bottom for easier printig. The original by MakinThings:...
thingiverse
I disigned this to fit 2 x 120mm fans in the front of the Cooler Master Storm Trooper case without the use of the hdd bays
thingiverse
Optimized version of this thing: http://www.thingiverse.com/thing:16754
thingiverse
Added a bracket to stabilize the mount when only 1 SSD is attached, so you can use my design when you have only 1 SSD too, saving plastic and having space for a 2nd one. This thing was made with Tinkercad. ...Edit it online...
thingiverse
I just wanted a very simple drive holder that consumes little material and is easy and fast to print. ... I used a 1mm Nozzle.