head tracking ir 3d models
156783 3d models found related to head tracking ir.thingiverse
Bill of Materials 1 x 3d Printer and material 2 x thin cables two colors each about 20 cm 3 x Orsam SFH 485 P LEDs 1 x 10 Ohm Resitor 1/8 W Power rating 1 x Usb Cable for Power supply 2 x cable ties 2.5mm ////////////////////////////////// Updates:...
thingiverse
Head tracking with IR led compatible for Zip tie on headphones. ...Inspected from https://www.thingiverse.com/thing:260088
thingiverse
I do not recommend printing the diffusers if you are using wide-angle IR diodes. ...I have wide angle diodes and I found that the diffusers reduced their viewing angle and brightness, but if you have standard diodes your results may differ from mine.
thingiverse
Switch: Catalog #: 275-007 (http://www.radioshack.com/product/index.jsp?productId=3020764) Battery Holder: Catalog #: 270-080 (http://www.radioshack.com/product/index.jsp?productId=22874796) UPDATE [12/2/15]: I've added some spherical diffusers for...
thingiverse
This is a modified version of Jewcookie's excellent IR tracking clip that I made specifically for my AKG K241 vintage headphones, but it might also fit newer AKG K240 headphones. NOTE: Designed by a beginner and printed by a friend so material...
thingiverse
I would recommend viewing this link below to see what LEDs & Resistors you will need as IR LEDS tend to vary in volts/amps/etc.http://www.free-track.net/english/hardware/calcled If you have any questions, feel free to drop me a message. ... ~ iTrooper
cults3d
I only had 3mm IR LED lying around so I had to remix the design to fit my LEDs ^^
thingiverse
I only had 3mm IR LED lying around so I had to remix the design to fit my LEDs ^^
prusaprinters
I only had 3mm IR LED lying around so I had to remix the design to fit my LEDs ^^ Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 150 Infill: 20% Gyroid Filament: [ Prusament ASA...
thingiverse
Reflective clip for head tracking systems. Single-revolution thread for easy snap in and out of the headset. Reflective circles and clip fit together - I tried to scale it for a snug fit so no glue is needed. Give it a try and rescale the...
thingiverse
Instructions Print at least the Clip Model Check Free-Track.net for simple assembly instructions and information on what LEDs to use plus more detailed wiring information. I created the mount with a flat placement in mind and without through holes...
thingiverse
Made this to mount my AimxyZ Head tracking camera. ...Uses 2-20mm, 1-15mm and 1-25mm long M6x1.0 SHCS's and nuts Regards
thingiverse
But any other IR emitting LED´s will work as long as they have a spread of at least 90° For Power, a Simple Buck Boost Converter is used to step down the 5V voltage from the PC just a tiny bit, as to not overload the LED´s, as well as isolate...
thingiverse
DIY Aruco marker head tracking adapter with led light ( for dark environment )
thingiverse
DJI / Vista Head Tracking Gimbal. ... What you need: 1 X 9 gr Servo for Tilt 1 x 9 gr 240 deg Servo for Pan 30x30mm fan 2-2.5mm self tap screws Happy printing and flying :)
thingiverse
I've also included an appropriately sized wedge to give one side of the tracker a 10mm elevation, as sometimes the software will have issues maintaining accurate tracking if your tracker is mounted directly perpendicular to the camera angle. ... Wiki...
thingiverse
I created this model to mount a 100mm ArUco paper tracking marker to my headphones. The ArUco marker is glued to some a cardboard backing, and then glued to the ‘V’ shaped mounting part. For this, I just used a glue stick. The bottom piece is...
thingiverse
AA Battery powered version of a Track IR Clip. The switch is superglued to the frame. Materials required: -Wire -switch (clip off one of the contacts on the side) -30 Ohm resistor (yours depends the voltage of your LEDs. check out an...
thingiverse
This is a servo head for a RadioShack Ultrasonic Range Sensor and a Sharp IR GP2Y0A21YK0F Analog Distance Sensor. Recessed mounting holes for 9g servo horn, also has nice wire path. ...I'll be using this on my Deca WalkerBot -...
thingiverse
These designs include: - 3 point IR led arm -Quick connect/disconnect attachment for your headphone How to use: The IR arm simply slides into the connect/disconnect attachment to fasten it to your headphone. When you're done, just simply remove the...
thingiverse
Head tracking device For PC games parts ・Camera PS3_Eye ・Infrared filter ・Infrared emitting LED 5mm ・ 100 Ω Resistor ・Toggle switch NO - OFF ・3.7 V 520 mAh 30 C Lip Battery Walker or XK micro helicopter Vertical: 63.5 mm Width: 17.2 mm Thickness: 6.5...
thingiverse
Arduino Code (Servo handling): https://github.com/eried/LaserTurretKinect/blob/master/Arduino/LaserTurretKinect.ino Kinect Code (in progress, Head tracking uses the MS SDK, I am still thinking on making an auto calibration routine, i.e. ...finding a...
prusaprinters
Arduino Code (Servo handling): https://github.com/eried/LaserTurretKinect/blob/master/Arduino/LaserTurretKinect.ino Kinect Code (in progress, Head tracking uses the MS SDK, I am still thinking on making an auto calibration routine, i.e. ...finding a...
thingiverse
This design houses 2x TCTR5000 IR Sensor PCBs. It is a perfect design for building an Incremental encoder (e.g. an Arduino Hamster Wheel reader) or to allow a autonomos car to follow a black line. Holes in the lid allow to adjust sensor sensitivity...
thingiverse
DIY head tracking USB ball joint DIY head tracking USB Infrared LED irradiation angle variable model with ball joint Weight reduction by obtaining power from USB The joint part is not fixed By adding a ball joint Infrared LED made it possible to...
thingiverse
I remixed this IR head clip to fit onto my Sennheiser PC 350 SE Headset. ...It's mountable to the headset with two cable ties.
thingiverse
My original Track IR 5 snapped in half so I designed this new version to be a little more sturdy. ...Made to be used with https://www.thingiverse.com/thing:3557779
thingiverse
Made this stand for Track IR since I'm not mounting it on my computer monitor as its on a entertainment cabinet.. The top is pitched 10 deg and its 9.5" tall. Its designed to hold a magnet thats .374" in dia and .5" high. ... The rear of the stand has...
thingiverse
11.09.2017 I add new version, thicker walls, more sturdy and 4 holes for mounting. ... Small head track clip. Designed for Osram SFH 4244. ... I made it smallest as possible, works fine with open track and ps3eye.