headlight dust cover 3d models
152353 3d models found related to headlight dust cover.cults3d
An extended headlight dust cover for a 4th Gen (2009-2018) Ram 1500/2500/3500 with factory quad headliights. These will allow you to install aftermartket LEDs for high beams. Before installation, remove the O-ring from the factory dust cover and...
thingiverse
I purchased new led bulbs for my vehicle only to find out the headlight dust cover would need to be modified. This is how I modified it. Simply cut your headlight dust cover as pictured above. Print model. Combine the two. Enjoy! Designed for...
thingiverse
... was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/458UBSgC07I Made this to replace the dust cover on the rear of the head light housing Just push it on very good fit. ... For 2014 Corolla hatch with projection type head lights
cults3d
Vectra C xenon headlight dust cover. ...(diameter to 84mm) Tested several times!
thingiverse
Replacement for the headlight dust cover on a Ford Focus mk1 1999
thingiverse
I inherited a Volkswagen Jetta MK5 from a relative and discovered during routine maintenance that one of the headlight dust covers was missing. This allows water to enter the headlight assembly and corrode the electrical connections. After searching...
prusaprinters
Dipped beam headlight cover for kia ceed. ...required original rubber grommet.made for mounting HID headlightThere is also a version without the hole
thingiverse
Took the orginals and added some slots on the back to run wires through for HID/LED upgrades. ...
thingiverse
Chevy Colorado headlight dust cover extension designed to accept aftermarket LED headlight kits
cults3d
Vectra C halogen headlight dust cover to led lamp. ...(diameter to 104mm) Tested several times!
thingiverse
Increased in height dust cover for Toyota Corolla E150 headlights. It is made for placement in the equipment of LED lamps. Can be used as a replacement for the original dust cover. Увеличенный по высоте чехол от пыли для фар головного света Toyota...
thingiverse
There is another dome shaped cover on thingiverse, but when I printed it, it was oval, not round and the tabs were different lengths. I printed this in pla, and painted it afterwards. I printed it with tabs down, and used basic supports for the...
thingiverse
This is a replacement headlight dust cover cap for Audi A3 / 2004 or Smart ForFour / 2007. Original part number is 1305239225 (1 305 239 225 PP-GF30). Print with support. PETG is preferred due to less shrinking than ABS. Always adjust model size...
cults3d
Car Headlight lid - dust cover Opel astra with gasket
cults3d
The lid is replacement for 1305219121 Headlight cover for many brands of car manufacturers ie. Mercedes, Chrysler, .... ...I made it for my lost from Opel (Vauxhaul) Zafira C.
thingiverse
The lid is replacement for 1305219121 Headlight cover for many brands of car manufacturers ie. Mercedes, Chrysler, .... I made it for my lost from Opel (Vauxhaul) Zafira C. ...
thingiverse
Extended Dust Cover for Chevrolet Trax (Tracker) with LED Lamps for headlight (High and Low Bean)
thingiverse
This is a replacement dust cover for the Alfa Romeo 159, Brera or Spider (Model 939). It has been designed to be extra deep to allow for a modern LED style headlight bulb to be fitted. Equally it could hold a HID ballast. ... Enjoy!
thingiverse
This dust cover was created so I could install replacement headlight bulbs (LED) in my Kia Soul EV since the factory ones are flat. Print it in black gloss TPU from a bone stock Creality Ender3. You need to use the factory rubber seal. ... Print...
thingiverse
This is to replace the latch on the dust cover for the BMW e83 headlights, clean off the old latch pieces and just slide this in. Dust cover part number 1305239123 It holds nicely even if not glued. DO NOT glue, if you do it will be impossible to...
prusaprinters
This is to replace the latch on the dust cover for the BMW e83 headlights, clean off the old latch pieces and just slide this in.Dust cover part number 1305239123It holds nicely even if not glued. DO NOT glue, if you do it will be impossible to...
thingiverse
I noticed one of the covers got lost but I still had one left, so I decided to take some measurements and create it in Autodesk Fusion 360. This is a 99% fit. On mine, I still needed to adjust the gap between the pins and the body with a sharp...
thingiverse
This is for extending the dust cover when retrofitting HID projectors into the stock headlight housing.
thingiverse
dust cap for the headlight of a Hyundai Tucson. ... I lost one of the dust caps while replacing a headlight so i made this design to replace it. ...
grabcad
dust cap for the headlight of a Hyundai Tucson.I lost one of the dust caps while replacing a headlight so i made this design to replace it.*Note*This part was designed to be 3D printed. ...For printing instructions see https://bit.ly/2KlwuC8
prusaprinters
dust cap for the headlight of a Hyundai Tucson. I lost one of the dust caps while replacing a headlight so i made this design to replace it. Print instructionsThere are 2 printable parts, 1 dust cap and 1 seal ring. I recommend to print the dust cap...
thingiverse
Both modifications of an excellent design by https://www.thingiverse.com/thing:3852272 The flat sided one give slightly more room (exactly enough for my Fahren H11/9005 kit on a GMC Terrain 2017). The rounded one gives even more room but is a...
thingiverse
I made this replacement part to install LED lights which require more room. In the rsdoc file there are 2 version, 1 big, one small. ...The big one did not fit on the left zide
thingiverse
This is a dust cover for ford c-max mk2. ...I made it for replace xenon (d3s) bulbs with runstreet p6 d3s led. Because it was not fit with stock dust cover. ...You should make a hole for driver cables.