headphone cable clothing clip 3d models
209872 3d models found related to headphone cable clothing clip.thingiverse
... ...Flat cables are prone to causing a lot of noise when it scrapes against zippers and such, so this cable clip will help reduce that noice (and also keep the cable in place). Attach clip to cable, and fasten it to your clothes (t-shirt, jacket, etc.)
myminifactory
I designed these clips to prevent from headphone cables to tangle up, and to organise them better, without losing the clip.
thingiverse
I wanted to be able to keep the two cables together to make cable management less of a headache since my pug puppy keeps getting tangled in the cables when I'm playing iRacing, so I came up with these little S-shaped clips to do just that. The big...
thingiverse
Since I like to wear my bluetooth headphones around the neck and often only use one I needed some system to keep them in place. ... This simple clip can be put on the cable and used to hold it wherever its needs to be.
prusaprinters
Since I like to wear my bluetooth headphones around the neck and often only use one I needed some system to keep them in place. This simple clip can be put on the cable and used to hold it wherever its needs to be. Print instructionsSimple PLA seems...
prusaprinters
It hold the cable where you need it - for example when cable is too long. Print instructions0,15 layer 15% infill PETG to get better result use support and clear the hole with players and drill(not mandatory) Measure your cable and table thickness...
thingiverse
Remixed to quickly add a cable clip to the original headphone hook
thingiverse
# Minimal Earphone Cable Clip Small **earphone cable clip** which snags on the collar of the jacket to prevent the chord from pulling while running or doing other sport activities. Keeps the cable running upright, which is especially useful when...
prusaprinters
It's also a little bigger than what I'd wanted. Headphone/Earphone Clip by Nick C. What I like: the clip itself works much better, it's designed to be printed without supports, and it also grabs thin wires without a problem. What I didn't like: it's...
thingiverse
I did start by trying the other Shure BT1 clip already up here: https://www.thingiverse.com/thing:3100915 - but wanted a less bulky clip, and also found the wall thickness seemed like overkill (maybe just printer / print material differences?) And...
cults3d
This design arose from the need for a bracket to hang my headphones on the wooden ceiling above my setup. Since it is a bit high I needed a somewhat long bracket to be able to attach it to the wooden beam and reach it comfortably from below. The...
prusaprinters
My version of one these, along with a cable holder.Print in whatever material you wish! ...The tolerance of the M16 bolt should be enough for most printers. </p><p>Only tried printing with 0.4mm nozzle and 0.2mm layer height.</p><p>Enjoy!</p>
thingiverse
Customized version of https://www.thingiverse.com/thing:4762118 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4762118
thingiverse
A simple but effective face mask clip for drying the mask after usage and to extend lifetime. ...Could also be used to guide headphone cables whilst wearing the mask. Picture Shows clip at height 10mm. ... Print Duration 15 minutes.
thingiverse
This is a headphone hook for a 25mm desk (25.00_short_high_headphone_hook_sxs) with some modifications: * The hook has about a 1cm increase on the headphone rest to fit big headphones * The face has a Star Trek communicator badge on its face, so it...
cults3d
... cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for headphone/earphone wire as well.. Print a couple and use them to route the link cable to the back, up and then straight down your back. ...(see the photo)
thingiverse
... with a smaller diameter as its cable is thinner. Has a second clip on the outside for headphone/earphone wire as well.. Print a couple and use them to route the link cable to the back, up and then straight down your back. ...(see the photo)
thingiverse
... ubiquitous in Germany and it works pretty well. I know it is very bad to roll the cable like in the photo, but I do it like that anyway. To remove the need for folding the cable into the loop, the end of the cable can be clipped into the holder.
prusaprinters
This is a simple headphone hanger that can be clipped on to most desk or shelf edges. It's sized to fit standard 34mm (1-3/8") thick IKEA Linnmon style desktops. To adjust for different thickness desktops, simple scale in the slicer, or add rubber...
thingiverse
This Clothing 'Quick Clip' is designed to attach to any clothing via the use of M3 screws, to attach to the jacket pictured I used 6mm Pan Head M3 Screws. The full 'Quick Clip' collection -...
thingiverse
My first custom 3D printable model. ...Made to provide a cable guide for my MiniDisc Remote on my bag to prevent the cable from getting in the way or getting caught on something.
thingiverse
Hi! ... This is my clip for headphones cable, its quite good, i use it every day. Have nice time with that thing! ...:) I used 0,25mm Nozzle!
thingiverse
This is a new headphone clip. Used to keep your wires from dropping to the floor and help support the weight of the wires so the the earbuds can stay in your ear. ... Enjoy.
thingiverse
The clip fits best on a 34.5 mm speaker_stand if you use a 2 mm Crepla foam strip between it. See instructions Instructions Turn object 90 degrees over X Printed in PLA Nozzle: 220 C HBP Glass: 60 C...
myminifactory
This is to hold your headphone onto your clothes to keep them from dropping to the ground and acts as support for the weigh of the wires. The wires can be placed over or hidden underneath your shirt. It's flat. You can take your earbuds out of your...
thingiverse
This part was made with Tinkercad. ...Edit the part online at: https://tinkercad.com/p/acc001737a874c75/33 The idea is to stick it under my desk with 3M Command Adhesive and hang my Sennheiser headphones from it.
thingiverse
Clip for headphone cable fi3mm and magnes size:8mm x 1.2 ( or more)
thingiverse
Customized version of https://www.thingiverse.com/thing:4762118 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4762118
thingiverse
Easy to pin to my shirt now that there is a curl and more of a lip